Bedienungsanleitung Scheppach Air Force (Seite 19 von 168) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Spanisch, Polnisch, Schwedisch, Norwegisch, Finnisch)

781499

Zoom out

Zoom in

Vorherige Seite

1/168

Nächste Seite

 www.scheppach.com /  service@scheppach.com /  +(49)-08223-4002-99 /  +(49)-08223-4002-58

GB | 19

• The compressor may only be used in suitable

rooms (with good ventilation and an ambient tem-

perature from +5 °C to 40 °C). There must be no

dust, acids, vapors, explosive gases or inamma-

ble gases in the room.

• The compressor is designed to be used in dry

rooms. It is prohibited to use the compressor in

areas where work is conducted with sprayed water.

8. Attachment and operation

m Important!

You must fully assemble the appliance before

using it for the rst time!

Mains connection

• The compressor can be connected to any 220 -

240-240 V~ 50 Hz shock-proof socket which is pro-

tected by a 16 A fuse.

• Before you use the machine, make sure that the

mains voltage is the same as the operating voltage

(see the rating plate).

• Long supply cables, extensions, cable reels etc.

cause a drop in voltage and can impede motor

start-up.

• At low temperatures below +5°C, sluggishness

may make starting difcult or impossible.

ON/OFF switch (g. 1)

• To switch on the compressor, press the button (2)

on position I.

• To switch off the compressor, press the button (2)

on position 0.

Establishing connections (g. 3, 4)

m Attention! Switch the device off for this.

When doing so, hold the coupling rmly in order to

avoid injuries due to the hose springing back.

• Connect the tting of your compressed air tool to

the compressed air hose (5) of the compressor.

• To disconnect this coupling again, pull the quick-

coupling (4) back at the compressed air hose (5).

Using the tyre ination device (g. 6, 7, 8)

The compressed air tyre ination device (G) is used

to inate car tyres. With the corresponding accesso-

ries it can also be used to inate and regulate bicycle

tyres, inatable dinghies, air mattresses, balls etc.

Pressure can be released by actuating the vent valve

(7).

m Attention! The manometer has not been ofcially

calibrated! After inating, please check the air pres-

sure with a calibrated device.

Using an air blow gun

You can also use the tyre ination device (G) as an

air blow gun to clean out cavities and to clean soiled

surfaces and work equipment.

6. Technical data

Mains connection 220 - 240 V~ 50 Hz

Motor rating max. 1100 W

Operating mode S3 15%

Compressor speed 3750 min-1

Operating pressure approx. 8 bar

Theoretical intake

capacity approx. 180 (l/min)

Sound power level LWA 97 dB(A)

Uncertainty KWA 1.93 dB

Protection type IP20

Protection class II

Weight of the unit 5.5 kg

The noise emission values were measured in ac-

cordance with EN ISO 3744.

Wear hearing protection.

The effects of noise can cause a loss of hearing.

Residual risks

Comply with the stipulated maintenance and safety

instructions in the operating instructions.

Remain attentive at all times when working and keep

third parties at a safe distance from your work area.

Even when the device is being used properly, there

will always be certain residual hazards that cannot

be completely ruled out. The following potential haz-

ards can arise due to the type and design of the

device:

• Unintentional starting up of the product.

• Damage to hearing if the stipulated hearing pro-

tection is not worn.

• Dirt particles, dust etc. can get into the eyes or

face despite wearing safety goggles.

• Inhaling swirled up particles.

7. Before starting the equipment

Before you connect the equipment to the mains sup-

ply make sure that the data on the rating plate are

identical to the mains data.

• Check the equipment for damage which may have

occurred in transit. Report any damage immedi-

ately to the transport company which was used to

deliver the compressor.

• Install the compressor near the point of consump-

tion.

• Avoid long air lines and supply lines (extension

cables).

• Make sure that the intake air is dry and dustfree.

• Do not install the compressor in a damp or wet

room.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Scheppach Air Force Seite 19

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info