Bedienungsanleitung Scheppach Basa 5.0 (Seite 23 von 148) (Alle Sprachen)

781468

Zoom out

Zoom in

Vorherige Seite

1/148

Nächste Seite

diverted from their work.

• The working space on the machine must be free

of chips and wood scrap.

• Wear only close-tting clothes. Remove rings,

bracelets and other jewelry.

• Always wear safety goggles when working.

• Wear a cap or hair net to protect long hair.

• Wear suitable gloves to change the sawband.

• Do not wear work gloves when working on the

saw.

• Observe the correct rotational speed setting on

the machine.

• The safety mechanism on the machine may not

be removed or rendered unusable.

• Cleaning, changing, calibrating, and setting of

the machine may only be carried out when the

motor is switched off. Pull the power supply plug

and wait for the rotating tool to completely stop.

• Connection and repair work on the electrical

installation may be carried out by a qualied

electrican only.

• All protection and safety devices must be repla-

ced after completing repair and maintenance

procedures.

• Switch the machine off and pull power supply

plug when rectifying any malfunctions.

• Use a suction unit to suck up wood shavings

and sawdust. The current speed at the suction

connection piece should be 20 m/s.

• Check the saw band guide and the saw band

tension before starting up.

• Do not use nicked saw bands or those that have

an altered form.

• Replace table inserts that have worn saw slots.

• When sawing round wood, make sure that the

work piece does not turn.

• For sawing heavy or cumbersome pieces, use

the appropriate working aids for bracing.

(Special accessory roller stands).

• Place the upper saw band guide as closely as

possible to the work piece.

• On slanted table plates, attach the longitudinal

stop on the lower table plate half.

• Do not brake the saw band with side pressure

after switching off.

• Remove work pieces that have become stuck

only with the motor switched off and with the saw

band at a standstill.

• Cut off the external power supply of the ma-

chine even if only minor changes of place are

envisaged. Properly reconnect the machine to

the supply mains before recommissioning.

• When leaving the work place, switch the motor

off. Pull the power supply plug.

 Use only as authorized

 CE tested machines meet all valid EC

machine guidelines as well as all relevant

guidelines for each machine.

• All protective and safety device must be moun-

ted on the machine before beginning work.

• The machine is designed to be operated by one

person. The operator is responsible for all other

persons in the working area.

• Observe all safety instructions and warnings

attached to the machine.

• See to it that safety instructions and warnings

attached to the machine are always complete

and perfectly legible.

• The bandsaw with the supplied tools and acces-

sories is designed exclusively for sawing wood,

material similar to wood, and non- ferrous metals

and steel.

• The maximum dimensions for workpieces to be

processed is may not exceed the bench size in

the standard version. Clearance width: 440 mm,

Clearance height: 300 mm

• For larger workpiece dimensions which require

tipping of the table top, the table extension or

the dolly (special accessories) must be used.

• The band saw can also be used for sawing me-

tal when it is equipped with a special saw band

dolly (special accessory) and a operated at an

adapted cutting speed. Metal allows with more

than 80 % magnesium may not be processed

due to the danger of res.

• When used in enclosed rooms, the machine

must be connected to a vacuum exhaust unit.

Use the dust extractor to remove matchwood or

saw dust. The vacuum support ow rate must be

20 m/s. Subatmospheric pressure 860 Pa.

• The automatic switching unit is available as a

special accessory.

Type ALV 2 Art. No. 7910 4010 230 V/50 Hz

Type ALV 10 Art. No. 7910 4020 400 V/230

V/50 Hz

• The vacuum exhaust unit automatically switches

on after a 2-3 second delay after the machine

tool is turned on. This avoids overloading the

circuit fuse.

• After turning off the machine tool, the vacuum

exhaust unit remains on for an additional 2-3

seconds and is then automatically switched off.

Remaining dust is thereby removed by vacuum

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Scheppach Basa 5.0 Seite 23

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info