Bedienungsanleitung Scheppach Basa 7.0 (Seite 18 von 92) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Schwedisch, Norwegisch, Finnisch)

782165

Zoom out

Zoom in

Vorherige Seite

1/92

Nächste Seite

DGB

Set-Up

Prepare the workplace where the machine is to

be placed. Insure sufcient room to allow safe

work without malfunctions. The machine is de-

signed to operate in closed rooms and must be

placed stabily on rm level ground. Stability

is insured by attachment to the ground with 4

screws.

At least 2 persons are required to lower the

machine from the pallet. Starting in the working

position, tip the machine to the left and pull out

the pallet to the right

Working Information

The following recommendations are examp-

les of the safe use of band saws.

The following safe working methods should be

seen as an aid to safety. They cannot be applied

suitably completely or comprehensively to every

use. They cannot treat every possible dange-

rous condition and must be interpreted carefully.

• Connect the machine to a suction unit when

working in closed rooms. A suction device

which conforms with commercial regulations

must be used for suction in commercial areas.

• Loosen the sawband when the machine is not

in operation (e.g. after nishing work). Attach

a notice on the tension of the saw band to the

machine for the next user.

• Collect unused sawbands and store them

safely in a dry place. Check for faults (teeth,

cracks) before use. Do not use faulty saw-

bands!

• Wear suitable gloves when handling saw-

bands.

• All protective and safety devices must be secu-

rely mounted on the machine before beginning

work.

• Never clean the sawband or the sawband gui-

de with a hand-held brush or scraper while the

sawband is running. Resin-covered sawbands

impair working safety and must be cleaned

regularly.

• For your own protection, wear protective glas-

ses and hearing protection. Wear a hairnet if

you have long hair. Roll up loose sleeves over

the elbows.

• Always position the sawband guide as near the

workpiece as possible when working.

• Insure sufcient lighting in the work area and

around the machine.

• Always use the fence for straight cuts to keep

the workpiece from tipping or slipping away.

• When working on narrow workpieces with

manual feed, use the push stick.

• For diagonal cuts, place the saw bench in the

appropriate position and guide the workpiece

on the fence.

• To cut dove-tails and dove-tailed tenons or

wedges swing the saw bench to the plus or mi-

nus position. Insure safe workpiece guidance.

• For arced and irregular cuts, push the workpi-

ece evenly using both hands with the ngers

together. Hold the workpiece with your hands

on a safe area.

• Use a pattern for repeated arced or irregular

cuts.

• Insure that the workpiece does not roll when

cutting round pieces.

• Use the traverse cutting gauge special ac-

cessory for safety when making traverse cuts.

• To safely cut round plates, use the circular

cutting unit special accessory.

Electrical connection

The installed electric motor is connected

and is ready to work.

The connection complies with the relevant VDE

and DIN regulations.

The customer-side mains supply and the

used extension line must meet these regula-

tions. Installations, repair, and maintenance

work relating to the electric installation may

only be performed by specialists.

Important Notes

The electric motor has been designed for the S

1 operating mode.

In case of an overload of the motor, it turns off

automatically. After a cooling period (duration

varies), you can turn on the motor again.

Defective Electric Connection Lines

Often, insulation damages occur on electrical

connection lines.

Causes are:

1. Drag marks if connection lines are led through

window or door clearances.

2. Kinks due to improper attachment or routing

of the connection line.

3. Cuts caused by running over the connection

line.

4. Insulation damages caused by pulling the

connection line out of the wall socket.

5. Fissures caused by the ageing of the insula-

tion.

Such defective electric connection lines

must not be used and are hazardous due to

the insulation damages.

Regularly check the electrical connection lines

for damages. Please make sure that the con-

nection lines are disconnected from the mains

supply during the check.

Electrical connection lines must comply with

the relevant VDE and DIN regulations. Only use

connection lines labelled with H 07 RN. The

labelling of the connection cable with the type

specication is required.

AC motor

1. The supply voltage must be 230 V / 50 Hz.

2. Extension lines up to a length of 25 m must

have a cross section of 1.5 square millime-

tres. Extension lines with a length of more than

25 m must have a minimum cross section of

2.5 square millimetres.

3. The mains connection is protected with a

delay-action fuse of 16 A.

Rotary current motor

1. The supply voltage must be 400 V / 50 Hz.

2. Mains supply and extension line must be ve-

wire = 3 P + N + SL.

3. Extension lines must have a minimum cross

section of 1.5 square millimetres.

4. The mains connection is protected with a

maximum of 16 A.

5. In case of mains supply or change of location,

the direction of rotation must be checked. If

required, the polarity must be reversed.

If you have further questions, please specify

the following:

1. Motor manufacturer

2. Kind of current of the motor

3. Data from the machine type plate

4. Data from the switch type plate

If you return the motor, always return the

complete drive unit with the switch.

Maintenance

Carry out retting, setting measurement

and cleaning work only when the motor is

switched off. Pull the plug and wait for the

sawband to come to a full stop.

An experience worker can carry out minor-

repairs on the machine himself.

Repair and maintenance work on the elec-

trical

system may only be carried out by a quali-

ed

electrician.

All protective and safety devices must be re-

attached immediately after completed repair

and maintenance work.

We recommend:

• The swinging segments of the bench, the saw-

band tensioning unit and the guide of the

cutting height adjustment unit must always

move easily.

Treat these parts with a lubricant spray when

necessary to maintain these functions.

• Clean the sawband regularly. Wood leaves

resin remnants which stick to the sawband and

impair working safety and performance.

• Keep the bench surface free of resin.

• Do not use cleaning agents or thinners which

are easily ammable or which emit harmful

vapors to clean the sawband and bench.

Use the concentrated resin remover special

accessory.

• Check sawbands regularly for faults. Replace

faulty sawbands immediately.

• Check saw bench insert.

Replace wom saw bench insert.

• Rubber lining of the band wheels

The rubber lining of the band wheels becomes

ripped and worn by the metal sawband over

time.

Exact sawband alignment is then no longer

possible. Working safety and performance are

impaired.

Replace the band wheels!

Replacement wheels can be ordered from your

scheppach dealer as with allother replace-

Scheppach Basa 7.0 Seite 18

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info