Bedienungsanleitung Scheppach BCH5300BP (Seite 32 von 84) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Polnisch)

781392

Zoom out

Zoom in

Vorherige Seite

1/84

Nächste Seite

32 GB

12. Disposal and recycling

The equipment is supplied in packaging to prevent it

from being damaged in transit. The raw materials in

this packaging can be reused or recycled. The equip-

ment and its accessories are made of various types

of material, such as metal and plastic. Defective

components must be disposed of as special waste.

Ask your dealer or your local council.

13. Troubleshooting

The table below contains a list of fault symptoms and

explains what you can do to remedy the problem if

your equipment fails to work properly. If the problem

still persists after working through the list, please

contact your nearest service workshop.

Important hint in case of sending the equipment

to a service station:

Due to security reasons please see to it that the

equipment is sent back free of oil and gas!

Putting the equipment back into operation

1 Remove the spark plug (see section 10 Change

and clean the spark plug).

2 Quickly tug on the starter cord to remove excess

oil from the combustion chamber.

3 Clean the spark plug and check that the electrode

gap is correct, or insert a new spark plug with the

correct electrode gap.

4 Prepare the equipment for operation.

5 Fill the tank with the relevant mixture of fuel and

oil. See the section „Fuel and oil“.

Transport

To transport the machine, empty the petrol tank as

described in section 8 draining fuel. Clean coarse dirt

off the equipment with a brush or hand brush.

Fault Possible cause Remedy

The equipment does

not start • Correct starting procedure not followed

• Sooted or damp spark plug

•

• Incorrect carburetor setting

• Blade or nylon cutter mounted incorrectly

• No fuel in the tank

• Follow the instructions for starting

• Clean the spark plug or replace it with a new

one

• Contact an authorized customer service outlet

• Reassemble the blade or nylon cutter

• Check the fuel level

The equipment starts

but does not develop

its full power

• Incorrect choke lever setting

• Soiled air  lter

• Incorrect carburetor setting

• Cutting blade blunt

• Set the choke lever on the position

• Clean the air lter

• Contact an authorized customer service outlet

• Have cutting blade resharpened /replaced

The engine does not

run smoothly

• Incorrect electrode gap on the spark plug

• Incorrect carburetor setting

• Clean the spark plug and adjust the electrode

gap, or  t a new spark plug

• Contact an authorized customer service outlet

Engine smokes exces-

sively

• Incorrect fuel mix

• Incorrect carburetor setting • Use the correct fuel mix (see fuel mixing table)

• Contact an authorized customer service outlet

If the temperature of

machines is too high • Engine is overloaded • Insure the machines have rest at regular time

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Scheppach BCH5300BP Seite 32

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info