Bedienungsanleitung Scheppach BCH5300BP (Seite 31 von 84) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Polnisch)

781392

Zoom out

Zoom in

Vorherige Seite

1/84

Nächste Seite

31GB

Replacement parts / accesories:

For the cutting equipment listed here, you can always

use the safety guards provided with the unit.

Grass trimmer/brush cutter:

Spool with Ø 450 7910700707

Blade with 3 teeth Ø 255 x 1.4 7910700702

Transport guard for blade 3 teeth 3904801065

Blade with 4 teeth Ø 255 x 1.5 7910700705

Transport guard for blade 4 teeth 3904801066

Blade with 8 teeth Ø 255 x 1.5 7910700711

Transport guard for blade 8 teeth 3904801066

Safety shield for grass trimmer 3904803034

11. Storage

Cleaning

• Keep handles free of oil, so you always have a se-

cure hold.

• Clean the equipment as required with a damp cloth

and, if necessary, mild washing up liquid.

mImportant!

• Always pull out the spark boot plug each time be-

fore carrying out any cleaning.

• Never immerse the equipment in water or other liq-

uids in order to clean it.

• Store the chainsaw in a safe and dry place out of

the reach of children.

Storage

Important: Never put the equipment into storage for

longer than 30 days without carrying out the follow-

ing steps.

Storing the equipment

If you intend to store the equipment for longer than 30

days, the equipment must be prepared accordingly.

Otherwise the fuel still remaining in the carburetor will

evaporate and leave a rubbery sediment. This can

cause problems when starting up the equipment and

may require expensive repairs.

1 Slowly remove the fuel tank cap to release any

pressure that may have formed in the tank. Care-

fully empty the tank.

2 To remove the fuel from the carburetor, start the

engine and let it run until the equipment stops.

3 Leave the engine to cool (approx. 5 minutes).

4 Remove the spark plug (see section 10 Change

and clean the spark plug).

5 Add one teaspoon of 2-stroke engine oil into the

combustion chamber. Slowly pull the starter cord

several times to apply a layer of oil to all internal

components. Fit the spark plug again.

Note: Store the equipment in a dry place and far

away from possible ignition sources such as an oven,

a gas- red hot water boiler, a gas- red dryer, etc.

Clean the air lter Fig. 37 - 40

Soiled air lters reduce the engine power by supply-

ing too little air to the carburetor. Regular checks are

therefore essential.

• Unclip the air lter cover and remove the sponge

lter element.

• To avoid objects falling into the air tank, replace

the air lter cover.

• Wash the lter element in warm soap water, rinse

and allow drying naturally.

Important: Never clean the air lter with petrol or

inammable solvents.

m Warning!

Never run the engine without the air lter ele-

ment installed.

Lubricate angle transmission

Lubricate with lithium-based grease. Remove the

screw and put in the grease, turning the shaft manu-

ally until grease emerges, then replace the screw.

Adjusting the idle speed Fig. 52

If the cutting device runs idle, correct the idle speed.

1. Allow the engine to warm for 3-5 minutes

(No high speeds!).

2. Turn the adjusting screw (S): clockwise

- idle speed increases (+)

counterclockwise

- Idling speed decreases (-)

The idle speed is 3000 min-1

Contact the manufacturer if the cutter continues to

run at idle.

Do not continue to operate the unit!

Storing the unit

After cutting, clean the unit thoroughly. Store the unit

in a dry room allow the motor to cool down before-

hand.

Important hint in case of sending the equipment

to a service station:

Due to security reasons please see to it that the

equipment is sent back free of oil and gas!

Ordering replacement parts

Please quote the following data when ordering re-

placement parts:

• Type of machine

• Article number of the machine

•

Service information

Please note that the following parts of this product are

subject to normal or natural wear and that the following

parts are therefore also required for use as consumables.

Wear parts*: Line spool, cutting blade, spark plug, air l-

ter

* Not necessarily included in the scope of delivery!

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Scheppach BCH5300BP Seite 31

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info