Bedienungsanleitung Scheppach BCH5300BP (Seite 29 von 84) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Polnisch)

781392

Zoom out

Zoom in

Vorherige Seite

1/84

Nächste Seite

29GB

2. Turn the engine switch (6) to the ON position. Fig.

30, 31

3. Put the choke lever on the position. Fig. 31

4. Press the fuel pump more than 5 times. Fig. 32

5. Pull the recoil starter handle (11) 3-5 times to

start the engine. Fig. 33

6. Pull the rope until engine starts. Fig. 33

7. Wait a while adjust the choke lever to posi-

tion. Fig. 34

8. To start the cutting tools, operate the release le-

ver (7) with the palm of your hand, and the throttle

lever (8) with your ngers. The further you push

the throttle lever, the higher the motor speed.

When releasing the throttle lever, the motor be-

comes idle and the cutting tools stop. Fig. 30.

The cutting tools should not continue turning and

should not move when the motor is idle. Fig. 30

9. Adjusting line length when working:

This machine is tted with a “Tap & Go” head.

To release more line, tap the cutting line head

against the round with engine at top speed: the

line will be released automatically and the knife

cut off the excess length. Fig. 48

10. If meet any problems, press the engine switch to

off position, the machine will stop running. If need

stop cutting head working, release the throttle le-

ver (8). Fig. 30

11. In an emergency, the safety button (m) can be

pressed from the harness. The machine then de-

taches immediately from the carrying strap and

falls to the ground. Fig. 28

12. If the machine is hot, the throttle level can be ad-

justed to ON position directly when re start the

machine.

Note: If the engine does not start up even after sev-

eral attempts, read the section „Engine troubleshoot-

ing“.

Note: Always pull the starter cord out in a straight

line. If it is pulled out at an angle, then friction will oc-

cur on the eyelet. As a result of this friction, the cable

will become frayed and will wear away faster. Always

hold the starter handle when the cable retracts.

Never allow the cable to snap back when it has been

pulled out.

Note: Do not start the motor in tall grass.

m Attention: When the engine has been switched

off, the cutter continues running for several seconds

therefore do not close to cutting head of brush cutter

until the cutter has come to a standstill!

9. Working instructions

Extending the cutting line

Caution! Do not use any kind of metal wire or metal

wire encased in plastic in the line spool. This may

cause serious injuries to the user. To extend the cut-

ting line, run the engine at full speed and tap the line

spool on the ground. This will automatically extend

the line. Fig. 48

The blade (A) on the safety shield will cut the line to

the appropriate length. Fig. 24

mImportant: Remove all grass and weed remnants

at regular intervals to prevent the shaft tube over-

heating. Lawn, grass and weed remnants become

trapped under the safety shield and prevent the shaft

tube from receiving adequate ventilation. Remove

the remnants carefully using a screwdriver or the like.

Fig. 49

Different cutting methods

When the equipment is correctly assembled it will cut

weeds and long grass in places which are dif cult

to access, e.g. along fences, walls and foundations

and also around trees. It can also be used for „mow-

ing“ down vegetation so that a garden can be better

prepared or a certain area cleared down to the soil.

Fig. 50

m Attention: Even if it is used carefully, cutting

around foundations, stone or concrete walls, etc. will

result in the line suff ering more than normal wear.

Trimming/mowing

Swing the trimmer from side to side in a scything

motion. Always keep the line spool parallel to the

ground. Check the site and decide which cutting

height you require. Guide and hold the line spool at

the required height to obtain an even cut. Fig. 50

Low trimming

Hold the trimmer right in front of you at a slight angle

so that the underside of the line spool is above the

ground and the line strikes the correct target. Always

cut away from yourself. Never draw the trimmer to-

wards yourself.

Cutting along fences/foundations

Approach wire mesh fences, lath fences, natural

stone walls and foundations slowly so that you can

cut close to them without striking the obstacle with

the line. If, for example, the line strikes stones, stone

walls or foundations, it will wear or fray. If the line

strikes wire fencing, it will break.

Trimming around trees

When trimming around tree trunks, approach slowly

so that the line does not strike the bark. Walk around

the tree, cutting from left to right. Approach grass or

weeds with the tip of the line and tilt the line spool

forwards slightly.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Scheppach BCH5300BP Seite 29

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info