Bedienungsanleitung Scheppach BCH5300BP (Seite 28 von 84) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Polnisch)

781392

Zoom out

Zoom in

Vorherige Seite

1/84

Nächste Seite

28 GB

4. Assemble and disassemble the cutting head

grass trimmer / nylon cutting head. Fig. 19 - 20

• Release the nut.

Line up the two holes of ange and shield, use

one screw driver to hold the ange as below and

turn the socket wrench clockwise, the nut will be

released.

• Fit the Nylon cutting head.

Remove another shield after release the nut. Still

hold the ange, take the Nylon cutting head on the

shaft and rotate counter-clockwise, the Nylon cut-

ting head is tted. Fig. 20

• Release the Nylon cutting head.

Use screw driver to hold ange and then rotate the

Nylon cutting head clockwise, it will be replaced.

Brush cutter / Cutter blade

• Fit the blade. Fig. 16 - 18

Take the outer ange off after release the nut, then

put the blade (4), outer ange (25), shield (24) and

nut according to priority as below picture. Note

the blade rotation direction needs be same as be-

low picture. Use screw driver to hold ange and

tighten nut counter-clockwise, ensure the nut is

tightened enough.

• Release blade. Use screw driver to hold ange and

release nut, the blade can be took off.

5. Assemble the safe guard. Fig. 21 23

• Fix the safe guard with hex key and wrench en-

closed as stardard accessories for tighting the nuts

enough. Please see the below pictures showing.

•

m Warning! Use only original manufacturer‘s re-

placement parts, accessories and attachments. Fail-

ure to do so can cause poor performance, possible

injury and may void your warranty. Never use the

machine without the guard assembled!

mWarning!

Please make sure the cutting head has been assem-

bled correctly before use!

Note: The packaging material is made of recycle

materials. Dispose of packaging materials in accord-

ance with regulations.

6. Fit the belt. Fig. 25 - 29

• Wear the shoulder strap. Fig. 25 - 27

• Balance the machine when the tool is switched off.

• When standing in a normal working posture, the

blade should touch the ground during normal work-

ing position.

• To t the backpacks to your body size adjust the

straps at the carrying strap. Fig. 29

• Safety button at the carrying strap Fig. 28

ATTENTION! In an emergency, the safety button

(m) can be pressed from the harness. The machine

then detaches immediately from the carrying strap

and falls to the ground.

OPERATION

When working with the equipment, the appropriate

plastic guard hood for cutting blade mode or cutting

line mode must be  tted to prevent objects being

thrown out by the equipment.

The integrated blade in the cutting line guard hood

automatically cuts the line to the optimum length.

Fig. 24

Filling with fuel

mDanger of injury! Fuel is explosive!

Turn off and cool the motor down before lling

the tank with fuel. You must observe all safety

instructions relating to handing fuel.

mRisk of device damage!

The device is supplied without motor or gear-

box oil.

ATTENTION! Before operating, you must ll it

with fuel.

• Unscrew the tank cap (B) and remove it. Fig. 32

• Pour in the fuel carefully. Avoid spilling!

• Screw the tank cap on rmly by hand.

Draining fuel. Fig. 47

• Hold a collection container beneath the fuel drain

bolt.

• Unscrew the tank cap (B) and remove it.

• Allow the fuel to run out completely.

• Screw the tank cap on rmly by hand.

Start on the unit

Do not start the unit until it has been completely as-

sembled.

mDanger of injury!

Do not operate the device unless you did not

nd any faults. If a part has become defective,

make sure to replace it before you use the device

again.

Check before use!

• Check the safe condition of the device:

• Check the device for leaks.

• Check the device for visual defects.

• Check that all parts of the device have been se-

curely tted.

• Check that all safety devices are in proper condi-

tion.

mDanger of injury!

Before starting work, always check the ground and

remove all objects which could be thrown by the de-

vice.

Start Fig. 30 - 34 + 48

Once the machine has been set up properly, start the

engine as follow:

1. Set the equipment down on a hard, level surface.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Scheppach BCH5300BP Seite 28

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info