Bedienungsanleitung Scheppach Bestcombi 310 Kity (Seite 19 von 35) (Deutsch, Englisch, Französisch)

782109

Zoom out

Zoom in

Vorherige Seite

1/35

Nächste Seite

Machine Environmental data

Operation: Altitude <=1000m, Temperature:

5~40Celsius Degree, Humidity: 40Celsius De-

gree <=50%, 20Celsius Degree <=90%

Transportation & storage temperature (Celsius

Degree): -25~+50

Noise emission

Planer

Noise output level in dB (jointing)

LWA idle run = 92.8 dB(A)

LWA processing = 95.1 dB(A)

Noise pressure level at workplace in dB

(jointing)

LqAeq idle run = 75.6 dB(A)

LqAeq processing = 78.5 dB(A)

Noise output level in dB (planing)

LWA idle run = 93.2 dB(A)

LWA processing = 96.6 dB(A)

Sound pressure level at workplace in dB

(planing)

LqAeq idle run = 76.7 dB(A)

LqAeq processing = 79.8 dB(A)

Saw

Noise output level in dB

LWA idle run = 95.4 dB(A)

LWA processing = 99.6 dB(A)

Sound pressure level at workplace in dB

LqAeq idle run = 78.6 dB(A)

LqAeq processing = 83.2 dB(A)

Milling machine

Noise output level in dB

LWA idle run = 93.3 dB(A)

LWA processing = 96.9 dB(A)

Sound pressure level at workplace in dB

LqAeq idle run = 78.5 dB(A)

LqAeq processing = 81.2 dB(A)

Noise characteristic values / measurement

conditions

The specied values are emission values and

need not simultaneously represent safe labour

values. Though there is a correlation between

emission and immission levels,

one cannot derive from this correlation reliably,

whether additional precautionary measures are

necessary. Factors that can inuence the exis-

ting immission level at the current workplace,

contain the duration of the effects, the peculia-

rity of the work room, other noise sources etc.,

e.g., the number of machines and operations in

the vicinity.

The permissible labour values may also vary

from country to country. This information should

however enable the user to make a better as-

sessment of the involved dangers and risks.

For the mentioned emission values, a measure-

ment safety allowance of

K = 4 dB is applicable.

Data on dust emission

The dust emission values measured in ac-

cordance with the “principles of testing dust

machines (concentration parameters) before

wood processing machines” of the Wood Spe-

cialized Committee lie below 2 mg/m3. Hence,

while connecting the machine to a proper and

effective vacuum cleaner with min. 20 m/s air

speed, one can presume a permanently safe

observation of the TRK threshold for wood dust

applicable in the Federal Republic of Germany.

Use hearing- or ear protection.

Use protective masks and goggles.

Use eye protection.

In this operating instructions manual, we

have used the following sign at places that

affect you safety: m

General instuctions

• Check all components for possible trans-

port damages after unpacking. In case of

complaints, the person responsible for the

delivery must be contacted. Complaints

made later shall not be entertained.

• Check to ensure that the delivery is com-

plete.

• Familiarize yourself with the device with the

help of the operating instructions manual

before using it.

• Use only original accessories as well as

consumables and spare parts. Spare parts

are available at your Scheppach specia-

lised dealer.

• Please quote our Article numbers as well as

type and year of manufacture of the device

in your orders.

NOTE:

According to the applicable Product Liability

Law, the manufacturer of this device shall not be

liable for damages to this device or damages

caused by this device in case of:

• Improper handling,

• Non-observation of the operating instruc-

tions manual,

• Repairs by third parties, unauthorized

tters,

• Installation and use of non-original spare

parts,

• Improper use of the machine,

• Failure of the electrical system due to the

non-observation of the electrical specica-

tions and VDE provisions 0100, DIN 57113

/ VDE0113.

We recommend the following:

Read the entire text of the operating instructions

manual before installation and start-up. This

operating instructions manual is expected to

help you familiarize yourself with the machine

and to use it as per the manufacturer’s instruc-

tions. The operating instructions manual con-

tains important instructions about how you can

work with the machine safely, economically and

properly, and about how you can avoid risks,

repair costs, reduce downtime and increase the

reliability and life span of the machine.

In addition to the safety provisions of this opera-

ting instructions manual, you must also observe

the specications of your country applicable to

the operation of the machine without fail.

Keep the operating instructions manual in a

plastic cover near the machine to protect it

against pollution and humidity. It must be read

carefully and observed by

all operators before starting work on the machi-

ne. Only persons who are trained to operate the

machine and have been instructed about the

associated risks may work on the machine. The

required minimum age must be observed.

In addition to the safety instructions listed in this

operating instructions manual and the special

regulations of your country, the universally reco-

gnized technical rules must also be observed.

General safety instructions m

• Forward the safety instructions to all per-

sons who work on the machine.

• Use the machine only if it is in a awless

condition technically, and only after lear-

ning about its proper and safe use, as well

as about the risks involved, complying with

the operating instructions! Get faults that

compromise safety in particular rectied

immediately

• Only tools that correspond to the European

Standard EN 847-1 may be used.

• All safety- and risk instructions on the

machine

• Keep all safety and risk instructions on

the machine in complete and readable

condition.

• The circular table saw may not be used to

cut rewood.

• Caution during work: Risk of physical injury

to ngers and hands from the rotary cutting

machine.

• Please ensure that the machine is stable

and that it is installed on rm ground.

• Check the mains power cables. Do not use

any faulty cables.

• Keep children away from the machine con-

nected to the power supply.

• The age of the operator should be minimum

18 years. Trainees must be minimum 16 ye-

ars old, but they can work on the machine

only under supervision.

• The attention of the persons working on the

machine should not be diverted

• If a second person is working at the circular

table saw to remove the cut workpieces,

the machine must be equipped with a table

extension. The second person should be

positioned only at the pick-up end of the

table extension.

• Keep the operator console of the machine

free of wood shavings and chips.

• Wear tight-tting clothes. Remove orna-

ments, rings and wrist-watches.

• Observe the direction of rotation of the

motor – see the electrical connection.

• The safety devices on the machine are not

to be dismantled or disabled.

• Conversion-, adjustment-, measurement-

and cleaning jobs are to be performed only

after the motor is switched off. Disconnect

the power plug and wait for the rotating

tool to stop.

• For troubleshooting, switch the machine off

and disconnect the power plug from the

mains socket.

• The machine must be connected to a va-

cuum cleaner during all operations. Please

observe the “Proper use according to

manufacturer instructions“ for this.

• When working on the machine, all safety

devices and covers must be installed.

• Install only well-sharpened, crack-free and

not-deformed saw blades.

• Circular saw blades made of high-perfor-

mance fast steel should not be installed.

• The safety devices on the machine are not

to be dismantled or disabled.

• The splitting wedge is an important safety

device which guides the workpiece and

prevents the closure of the saw kerf behind

the saw blade, and the rebounding of the

DGB

Scheppach Bestcombi 310 Kity Seite 19

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info