Bedienungsanleitung Scheppach Bestcombi 310 Kity (Seite 21 von 35) (Deutsch, Englisch, Französisch)

782109

Zoom out

Zoom in

Vorherige Seite

1/35

Nächste Seite

Description

Saw (Fig. A)

1. Sawing/milling machine table

2. Saw – protective hood

3. Saw blade

4. Splitting wedge

5. Saw inclination setting

6. Saw height adjustment

7. Carriage

8. Table support

9. Longitudinal stop

10. Saw/milling machine switchbox

Milling machine (Fig. B)

10. (A) Saw/milling machine switchbox

11. Protection and stop attachment

12. Lateral and vertical clamping device

13. Adjustable milling stops

14. Height adjustment of milling machine

15. Blocking lever of the height adjustment

16. Emergency-stop switch

Slide carriage for sawing and trunnion cut-

ting (Fig. B)

7. Carriage

8. Small delivery table

17. Cross-sectional stop

18. Permanently clamping lever

Jointer / planer (Fig. C)

19. Adjustable jointing table

20. Cutting depth adjusting wheel

21. Jointing delivery table

22. Detachable jointing stop, adjustable and

inclinable

23. Planer shaft guard, adjustable

24. Height adjustment wheel of planer

25. Vacuum suction hood for jointer

26. Jointer and planer switchbox

Tool and resources (Fig. D)

Slide rod

Slide handle

Detaching pin for saw blade replacement

Box wrench for saw blade

Open-end wrench for milling machine change

Allan wrench 4/5/6 mm

Open-end wrench 10/13/17 mm

Residual risks m

Circular saw (A)

The circular saw is designed for operations on

solid wood or derived wood materials. It is ideal

for longitudinal and format as well as bevel

cuts. Firewood and roundwood should not be

cut. Only hard metal covered saw blades that

correspond to the Directive EN 847-1 should be

used. Damaged saw blades must be replaced

immediately.

Table inserts with lined kerfs must be replaced

immediately. Please note that moving the wood

pieces on the machine table involves the risk of

physical injury.

The use of tools made of HSS steel is prohibi-

ted. Connect vacuum cleaner.

Milling machine (B)

Check before each start whether the tool can

rotate freely.

Always move the workpiece against the direc-

tion of rotation. Never work with free hands,

always use a stop or clamping device.

Use slide rod for small tools.

Do not exceed the specied rotary speed.

Connect vacuum cleaner.

Jointer and planer (C)

Adjust planer knife carefully.

Planer shaft guard must always cover the un-

used section of the knife shaft.

Use the slide handle for thin workpieces. Use

the slide rod for short workpieces. For the join-

ting and planing of special workpieces, prepare

a stencil which prevents the sudden rebound-

ing of the workpiece. Do not release the wood

during processing.

Do not allow your hands to get close to the tool

under any circumstances. Check the rebounding

lock regularly during planing. Connect vacuum

cleaner.

All installation and retro-tting jobs must

be performed after disconnecting the power

plug.

Residual risks may occur despite all preven-

tive measures, such as e.g.:

Injuries due to exposed tool or during tool

change.

Clothes getting entangled in moving machine

parts or the tool. Getting crushed under workpi-

ece guides and moving machine parts.

Injuries due to ying tool components after a

tool suffers breakage.

Injuries (suffered) due to ying workpiece parts.

Risk of re from ames or heat radiation. Risk

when working on the electrical system. Inhalati-

on of dust or poisonous vapours.

Transport

Transport protection: Wood lining

Delivery: Machine mounted on wood pallet

Caution: Collision or heavier loads must be

avoided, these can lead to damages to the

machine and to disturbances in the settings.

Unpacking

Unpack the machine preferably in the room in

which it will be operated

Deposit the machine with a crane at the provi-

ded place

Tie ropes only at the specied positions

Caution: Do not lift the machine by the tables

Disposal of packaging material

The packing protects the machine from trans-

port damages.

The packaging material can be recycled, and

can be reused in the waste management cycle.

Packaging components such as lms, plastic

and plastic bags can be dangerous for children.

There is risk of suffocation.

Keep the packaging components outside the

reach of children and dispose of them as fast as

possible

Installation / operation

Attention: Before operation, be sure to x the

machine on level concrete ground and start the

dust exhaust system rst.

The resistance of the hoses xed shall be less

than 1000000 ohm

Installation of the slide table

Unpack the slide table and put it on a table/

workbench.

Remove the two nuts from the screws mounted

on the bottom side of the slide table, and keep

them at a safe place. (will be required for subse-

quent installation)

Fig. E1

Take the table out and remove the plastic ap (1)

(do this on

both sides)

Fig. E2, E3

The stops (2, 3) for the slide table are already

set at the factory

Just place the table on the frame of the machine

(ideally with 2 persons).

Pull the Allen screw (4) softly with the help of the

wrench (on both sides), move the table towards

the Stop screws (2). You may now tighten the

Allen screws (4).

Fig. E4

Now screw the nuts that you removed from the

table at the start on the bolt of the table and tigh-

ten them uniformly

As nal control, place a straight rod on the slide

table, and check the surface of the machine

table. Ideally, the slide table is a couple of one-

tenth millimetres higher than the machine table

DGB

Scheppach Bestcombi 310 Kity Seite 21

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info