Bedienungsanleitung Scheppach BG150 (Seite 18 von 152) (Alle Sprachen)

781665

Zoom out

Zoom in

Vorherige Seite

1/152

Nächste Seite

18 GB

CHANGING THE GRINDING WHEELS

IMPORTANT NOTE: In order to prevent injuries from

accidentally starting the machine the machine’s main

switch must be turned off before changing a grinding

wheel. Pull power plug!

• Loosen the spark gard and the eye shield and pull out

• as far as possible. Do not remove these parts!

• Loosen work rest and pull out as far as possible.

• Dissemble screws and pull off end plate.

• Take off outside ange and the old grinding wheel,

then assmeble the new one.

Important note:

• Do not remove the pieces of card board on the sides

of the wheel, as they are intended for strengthening

the grip of the Flange against the grinding wheels.

• Examine the new grinding wheels on cracks or other

visible damages and dispose if necessary.

• Mount ange and nut again.

• Do not tighten the screw by force. This can cause the

grinding wheel to break.

• Mount end plate.

• Mount work rest, spark guard and eye shield accord-

ing to installation instructions.

Using the grinding wheel dresser

The grinding wheel dresser is a tool for straightening of

grinding wheels.

• Press lightly against grinding wheel – without cre-

ating sparks. Move the dresser sideways over the

entire width of wheel.

m Attention! Always wear safety goggles.

9. Cleaning and maintenance

Always pull out the mains power plug before starting

any cleaning work.

Cleaning

• Keep all safety devices, air vents and the motor

housing free of dirt and dust as far as possible.

Wipe the equipment with a clean cloth or blow it with

compressed air at low pressure.

• We recommend that you clean the device

immediately each time you have nished using it.

• Clean the equipment regularly with a moist cloth

and some soft soap. Do not use cleaning agents

or solvents; these could attack the plastic parts of

the equipment. Ensure that no water can seep into

the device. The ingress of water into an electric tool

increases the risk of an electric shock.

Maintenance

There are no parts inside the equipment which require

additional maintenance.

10. Electrical connection

The installed electric motor is factory connected ready

for operation. The connection meets the applicable VDE

and DlN regulations.

WARNING! Never connect the plug to power source

outlet until all installations and adjustments are complet-

ed and you have read and understood sthe safety and

operation instructions.

ASSEMBLY

Work Rests (Fig. 1, Nr. 4)

Install the work rest with a star grip screw and a washer

to the wheel guard. The distance between wheel and

work rest should not exceed 2 mm.

Spark Guards (Fig. 2)

Install the spark guard with a cross-head screw and a

washer to the wheel guard. The distance to the wheel

guard should not exceed 2 mm.

Wheel Guards (Fig. 3, Fig. 4)

1 Install the eye shield with 2 cross-head screw n M4, 2

washers and 2 hex nuts to the clamping plate.

2 Lead the handle into the clamping plate and x it with

a at head screw M6, a washer and a nut.

3 Fix the complete unit to the wheel guard with U-handle,

hex bolt M6 and a washer.

The guard is individually adjustable, as to protect the us-

ers eyes during grinding process.

8. Operation

On/Off switch (8)

• To switch on the equipment set the On/Off switch (8)

to position On.

• Move the On/Off switch (8) to position Off to switch

off the equipment.

After switching on, wait for the equipment to reach its

maximum speed of rotation. Only then should you be-

gin with the grinding.

Work practice

• Exert only moderate pressure on the workpiece so

that it can be machined at constant speed.

• Instead of accelerating your work, high pressure will

cause the drive unit to slow down and even stop,

thus overloading the motor.

• For your own safety, it is essential to secure small

workpieces with a screw clamp or vise.

Grinding

• Place the workpiece onto the workpiece support (4)

and slowly guide the workpiece towards the grind-

ing wheel (3) at the desired angle to the point where

workpiece and grinding wheel make contact.

• Move the workpiece slightly back and forth to pro-

duce an optimal grinding result. This way the grind-

ing wheel (3) will be evenly worn. Allow the work-

piece to cool down occasionally.

Important!

If the grinding wheel becomes jammed during op-

eration, remove the workpiece and wait until the tool

reaches its top speed again.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Scheppach BG150 Seite 18

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info