Bedienungsanleitung Scheppach BS2000 Primaster (Seite 28 von 46) (Deutsch, Englisch, Französisch)

782174

Zoom out

Zoom in

Vorherige Seite

1/46

Nächste Seite

28 GB

• When sawing, the workpiece must always be guid-

ed by its longest side.

Attention! When processing narrower workpieces it

is essential to use a push stick. The push stick (L)

must always be stored within reach, on the hook pro-

vided for this purpose on the side of the saw (Fig.

6.1).

10.3 Performing longitudinal cuts (Fig. 15)

Here, a workpiece is cut in its longitudinal direction.

• Position the longitudinal fence (5) on the left side

(if possible) of the saw band (Fig. 15), in accord-

ance with the desired width.

• Lower the saw band guide (4) onto the workpiece.

• Switch on the saw.

• Press one edge of the workpiece against the lon-

gitudinal fence (5) with the right hand, whilst the

at side lies on the saw bench (6).

• Slide the workpiece at an even feed rate along the

longitudinal fence (5) into the saw band (Fig. 15).

• Important: Long workpieces must be secured

against tipping at the end of the cutting process

(e.g. with reel-off stand, etc.)

10.4 Performing angled cuts (Fig. 13)

• Set saw bench to desired angle (see „Angled

cuts“).

• Perform the cut as described under „Performing

longitudinal cuts“.

10.5 Freehand cuts (Fig. 16)

One of the most important features of a band saw is

the ease with which it can cut curves and radii.

• Lower the saw band guide (4) onto the workpiece.

• Switch on the saw.

• Press the workpiece rmly onto the saw bench (6)

and slowly slide into the saw band.

• In many cases it is helpful to roughly saw curves

and corners approximately 6 mm from the line.

• If it is necessary to saw curves that are too tight

for the saw band used, auxiliary cuts must be sawn

up to the front face of the curve, so that these fall

off as wood waste when the nal radius is sawn.

Attention!

For all cutting operations, the upper saw blade guid-

ance (4) should be as close as possible to the work-

piece.

• To do this, open the adjustment handle for saw

blade safety device (13). (Fig. 1)

• Lower the upper saw blade guide (4) and the saw

blade guard (3) as close as possible to the work-

piece.

• Subsequently close the adjustment handle for for

saw blade safety device (13).

11. Cleaning and maintenance

Important.

Warning! Prior to any adjustment, maintenance or

service work disconnect the mains power plug!

General maintenance measures

Wipe chips and dust off the machine from time to

time using a cloth. In order to extend the service life

of the tool, oil the rotary parts once monthly. Do not

oil the motor.

When cleaning the plastic do not use corrosive prod -

ucts.

Cleaning

• Keep all safety devices, air vents and the motor

housing free of dirt and dust as far as possible.

Wipe the equipment with a clean cloth or blow it

with compressed air at low pressure.

• We recommend that you clean the device immedi-

ately each time you have nished using it.

• Clean the equipment regularly with a moist cloth

and some soft soap. Do not use cleaning agents or

solvents; these could attack the plastic parts of the

equipment. Ensure that no water can seep into the

device. The ingress of water into an electric tool i

creases the risk of an electric shock.

Maintenance

There are no parts inside the equipment which re-

quire additional maintenance.

12. Storage

Store the device and its accessories in a dark, dry

and frost-proof place that is inaccessible to children.

The optimum storage temperature is between 5 and

30˚C.

Cover the electrical tool in order to protect it from

dust and moisture.

Store the operating manual with the electrical tool.

13. Electrical Connection

The installed electric motor is connected and is ready

to work.

The connection complies with the relevant VDE and

DIN regulations.

The customer-side mains supply and the used exten-

sion line must meet these regulations.

Important information

In the event of an overloading the motor will switch

itself off. After a cool-down period (time varies) the

motor can be switched back on again.

Defective Electric Connection Lines

Often, insulation damages occur on electrical con-

nection lines.

Causes are:

1 Drag marks if connection lines are led through win-

dow or door clearances.

2 Kinks due to improper attachment or routing of the

connection line.

3 Cuts caused by running over the connection line.

4 Insulation damages caused by pulling the connec-

tion line out of the wall socket.

5 Fissures caused by the ageing of the insulation.

Such defective electric connection lines must not be

used and are hazardous due to the insulation dam-

ages.

Regularly check the electrical connection lines for

damages. Please make sure that the connection

lines are disconnected from the mains supply during

the check.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Scheppach BS2000 Primaster Seite 28

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info