Bedienungsanleitung Scheppach BSH500 (Seite 18 von 28) (Deutsch, Englisch, Italienisch)

782179

Zoom out

Zoom in

Vorherige Seite

1/28

Nächste Seite

english

With the aid of a 90° angle carry out a trial cut.

•

On the front left frame leg, attach the locking screw for

the saw blade key and the sliding pole.

1 cheese-head screw M5 x 40

2 washers 5

2 hex nuts M5

Stop brackets, Fig. 06

•

Attach the stop brackets (1)

each 1 carriage bolt M8 x 16

each 1 serrated washer 8,4

each 1 hex nut M8

Mounting blade with cover, Fig. 06

•

Insert the mounting blade (2) into the table and secure

with screws.

2 hex bolts M8 x 16

2 serrated edge washers 8,4

2 hex nuts M8

•

Screw the carrier arm pro le (3) onto the mounting

blade through the upper bore holes (saw blade ø 500

mm).

2 carriage bolts M8 x 45

2 washers 8

2 hex nuts M8

•

For the ø 400 mm saw blade, carry out the same as

above, but through the lower bore holes.

•

Attach covering cap.

1 carriage bolt M8 x 65

1 clamping sleeve 10 x 26

1 washer 8

1 hex nut M8

Attaching the splitting wedge, Fig. 06.1

•

The splitting wedge holder is already attached.

•

Loosen hex bolt M12 x 40 in the splitting wedge holder.

Do not remove!

•

Insert the splitting wedge (4) from above between the

clamp ing plate and the intermediate plate and only

slightly tighten hex bolt M12 x 40.

•

When installing the saw blade, the splitting wedge must

be correspondingly  tted. (See para. “H”)

Installing the saw blade, Fig. 07

•

Lower the height adjustment.

•

Remove the left-hand thread lock nut M20 and the

 ange.

•

Insert the saw blade from below and attach the  ange.

•

When tightening the hex nut, prevent the motor shaft

from turning by gripping it with the holding mandril.

Fig. 07.1

Should the  tted sawblade not sit parallel in the sawblade

slot – with the consequence that it fouls the table insert,

the complete sawblade guard box under the table must be

re-adjusted. Proceed as follows:

•

Lower the sawblade to about 50 mm cutting height.

•

Release the four  xing bolts of the sawblade guard box

under the table.

•

Slightly retighten the two hexagon bolts (1) and adjust

the saw blade guard box.

•

Tighten the hexagon bolts (1)  rmly and raise the

sawblade.

•

Check position of sawblade. It must be in line with the

holder of the sawblade guard. Use a ruler for testing.

•

Lower the sawblade again and tighten the hexagon bolts

(2).



Adjusting the splitting wedge, Fig. 08

The distance between the saw blade and the splitting

wedge must not exceed 10 mm.

After each saw blade change, recheck the setting and if

necessary, reset.

The tip of the splitting wedge must never be set lower than

the basic tooth height of the uppermost saw tooth. The

recommended setting is a maximum of 5 mm below the

uppermost saw tooth tip. The splitting wedge is an

important safety feature which feeds the work piece and

prevents the cut from closing as well as preventing the

work piece from kicking back. Please note the thickness of

the splitting wedge. See the numbers indicated on the

splitting wedge. The splitting wedge must not be less than

the thickness of the saw blade, and not thicker than the

width of the cut.

The splitting wedge must be aligned with the saw blade.

Fig. 08.1

Correct deviations in the following manner:

•

loosen hex bolts (1)

•

adjust splitting wedge prependicularly

•

loosely tighten hex bolts (1)

•

Align splitting wedge to saw blade and tighten the hex

bolts (1) again.

Ripping fence, Fig. 09

Screw the intermediante plate onto the stop tube. Do not

tighten.

2 carriage bolts M6 x 50

2 washers 6

2 wing nuts M6

Slide in the stop rail and clamp.

Position 1 = high surface

Position 2 = Iow surface

Insert the ripping fence into the clamping attachment.

To clamp = raise clamping  ap

To lower = press clamping  ap down

 Electrical connection

The installed electric motor is connected ready for oper ation.

Mains connection and any extension cables used must comply

with applicable regulations.

Motor braking unit

The

scheppach circular sawbench

for building sites is  tted

with an automatic motor braking unit which becomes effec-

tive as soon as the driving motor is switched off.

Important remark:

The electric motor is designed for the S 6/40 % operating

mode. Therefore, the motor is automatically switched off in

the event of an overload. The motor can be switched on

again after a cooling down period that can vary.



Defective electrical connection cables

Electrical connection cables often suffer insulation dam-

age.

Possible causes are:

•

Pinch points when connection cables are run through

window or door gaps.

•

Kinks resulting from incorrect attachment or laying of

the connection cable.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Scheppach BSH500 Seite 18

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info