Bedienungsanleitung Scheppach BTS800 (Seite 12 von 120) (Alle Sprachen)

644521

Zoom out

Zoom in

Vorherige Seite

1/120

Nächste Seite

english 9

Keep work area well lighted.

• Keep children away. All visitors should be kept at a safe

distance from the work area.

• Make your workshop kid proof. Lock your workshop. Tools

not used should be kept in a dry place, inaccessible for

children.

• Don’t force the tool. It will do the job better and safer at

the rate for which it was designed.

• Use the right tool. Don’t force the tool or attachment to

do a job for which is was not designed.

• Use proper extension cord. Make sure your extension

cord is in good condition. When using an extension cord,

be sure to use one heavy enough to carry the current

your product will draw. An undersized cord will cause a

drop in voltage resulting in loss of power and overheat-

ing.

• Wear proper clothing. Do not wear loose clothing, gloves,

neckties, rings, bracelets, or other jewelry which may

get caught in moving parts. Nonslip shoes are recom-

mended. Wear protective hair covering to contain long

hair. Roll your sleeves up to above the elbows.

• Protect your eyes by safety goggles. Everyday eyeglasses

offer only little protection. They are no safety glasses.

Wear a face or dust mask when working in a dusty envi-

ronment.

• Secure work. Use clamps or a vice to hold work, when

practical. It is safer than using your hand, and it frees

both hands to operate the tool.

• Don’t overreach. Keep proper footing and balance at all

times.

• Maintain tools with care. Keep tools sharp and clean for

best and safest performance. Follow the instructions for

lubricating, and changing accessories.

• Always disconnect the machine before servicing, and

when changing accessories, such as blades, bits, cut-

ters, and the like.

• Only use recommended accessories. Consult the operat-

ing instructions for the recommended accessories. The

use of improper accessories may cause risk of injury to

persons.

• Never stand on the machine. Serious injury could occur

if the machine is tipped or if the cutting tool is uninten-

tionally contacted.

• Check for damaged parts. Before further use of the tool,

a guard or other part that is damaged should be carefully

checked to determine that it will operate properly and

perform its intended function. Check for alignment or

binding of moving parts, breakage of parts, mounting,

and any other conditions that may affect its operation. A

guard or other part that is damaged should be properly

repaired or replaced.

• Direction of work. Push the workpiece towards the saw-

blade or cutter only in the moving direction of the tool.

• Never leave the machine unattended while it is running.

Wait until the tool has come to an absolute standstill,

before you leave the machine.

• Use the correct power connection. Do not pull the power

plug to stop the machine during work. Never remove the

plug from the socket by pulling the extension cord.

• Always stay attentive to what you are doing, even when

using the machine regularly. Bear in mind that a fraction

of a second is sufﬁcient to cause an injury.

• Keep your safety in mind. Safety is a combination of

common sense and staying alert as long as the machine

is switched on.

Additional safety rules for the belt and disc sanding machine

• WARNING: Do not use your machine until it is completely

assembled and installed according to the instructions.

• If you are not familiar with the operation of the sanding

machine, ask the head of the department, your teacher,

or any other qualiﬁed person.

• ATTENTION: This machine has only been designed for

sanding wood or similar materials. The sanding of other

materials can cause ﬁre, injuries, or damage the prod-

uct.

• Always wear safety goggles.

• This machine may only be operated indoors.

• IMPORTANT: Mount and use the machine on a horizontal

surface. A non-horizontal surface can damage the mo-

tor.

• If the machine tends to tilt or walk (especially when

sanding long and heavy panels), it must be fastened to a

solid surface of sufﬁcient carrying force.

• Make sure the sanding belt runs in the correct direction

– see arrows at the back of the belt.

• Make sure the sanding belt is running correctly so that it

cannot come off the drive pulleys.

• Make sure the sanding belt is not twisted or loose.

• Firmly hold the workpiece when sanding.

• Always use the fence when using the sanding machine

in horizontal position.

• Always hold the workpiece ﬁrmly to the table when using

the sanding disc.

• Always hold the workpiece to the side of the sanding

disc running downwards, in order to maintain the work-

piece pressed to the table. By using the upward-running

side of the sanding disc, the workpiece could be ejected

and cause injury to persons.

• Always keep a minimum distance of about 1.5 mm or

less between the table or fence and the sanding belt or

disc.

• Do not wear gloves. Do not hold the workpiece with a

cloth during sanding.

• Use sanding belt or disc of the correct grit corresponding

with the wood.

• Never sand workpieces too small to be held safely.

• Avoid awkward hand positions where a sudden slip could

cause your hand to touch the sanding belt or disc.

• When sanding a large piece of material, provide an ad-

ditional support at table height.

• Never sand an unsupported workpiece. Secure the work-

piece with the table or the fence. Exceptions are the

sanding of curved workpieces on the outside of the sand-

ing disc.

• Always clear the table, fence or sanding belt of scraps or

other objects, before turning the machine on.

• Do not perform any layout assembly or set-up work on

the table while the sanding machine is in operation.

• Switch the machine off and pull the power plug from the

socket when ﬁtting or removing accessories.

• Never leave the working area of the sanding machine

while the tool is running, or as long as it has not come to

an absolute standstill.

m Proper Use

The machine meets the currently valid EU machine directive.

• The manufacturer’s safety, operation and maintenance

instructions as well as the technical data given in the

calibrations and dimensions must be adhered to.

• Relevant accident prevention regulations and other gen-

erally recognized safety and technical rules must also be

adhered to.

• The machine may only be used, maintained or repaired

Hallo, ich habe eine bts800 dort ist die Antriebscheibe (76) des keilrippenriemen ausgeschlagen.
Wo bekomme ich Ersatz?

Mfg Melanie Etterer Eingereicht am 15-9-2021 23:09
Antworten Frage melden

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Lesen Sie zuerst die Anleitung;
Schauen Sie nach, ob die Frage bereits gestellt wurde;
Stellen Sie die Frage so deutlich wie nur einigermaßen möglich;
Erwähnen Sie was Sie bereits versucht haben um das Problem zu lösen;
Ist Ihr Problem von einem Besucher gelöst dann lassen Sie ihn / sie wissen in diesem Forum;
Falls Sie reagieren möchten, so verwenden Sie bitte das Antworten- Formular;
Da ihre Frage für alle Besucher sichtbar ist, sollten Sie lieber keine persönliche Daten erwähnen.

Neu registrieren

Registrieren auf E - Mails für Scheppach BTS800 wenn:

neue Frage gestellt werden
neue Handbücher vorhanden sind

Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.

Scheppach BTS800 Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.