Bedienungsanleitung Scheppach CMT200-20ProS (Seite 22 von 80) (Deutsch, Englisch, Französisch, Polnisch)

781444

Zoom out

Zoom in

Vorherige Seite

1/80

Nächste Seite

 www.scheppach.com /  service@scheppach.com /  +(49)-08223-4002-99 /  +(49)-08223-4002-58

22 | GB

Removing the rechargeable battery pack:

Press the release button (4) and remove the re-

chargeable battery pack.

Used batteries

If a fully recharged battery lasts for considerably

shorter operating times, the battery is used up and

needs to be replaced. Only use an OEM battery pack

replacement available from our Customer Service.

Switching on and off

To switch on the machine, slide the slide switch to

position “I (ON)”.

To switch off the machine, slide the slide switch to

position “O (OFF)”.

Adjusting the number of pendulum strokes (Fig.

The number of pendulum strokes is adjustable. To

change the number of pendulum strokes, turn the ad-

justing dial between 1 and 6. The higher the number,

the higher the number of pendulum strokes. Before

starting work, set the adjusting dial to the appropriate

number for your workpiece.

NOTE:

The adjusting dial cannot be turned directly from 1 to

6 or from 6 to 1. Continuing to turn the adjusting dial

by force may damage the machine. If you change the

direction of rotation of the adjusting dial, always move

it through all intermediate positions.

12. Operation

WARNING:

• Keep hands and face away from the application tool

before starting the machine and during operation .

Caution

• Do not exert excessive pressure on the machine as

this may cause the motor to block and the machine

to stop.

Cutting, sawing and scraping

CAUTION:

• Do not force the machine in the direction of use

(e.g. to both sides) without a cutting edge. This can

damage the machine.

• Set the application tool on the workpiece. Then

push the machine forward so that the movement of

the application tool does not slow down.

NOTE:

• Violent feeding or excessive pressure on the ma-

chine can reduce the performance of the work.

• Before starting cutting work, it is recommended to

preset the pendulum stroke number to 4 - 6.

• Remove sawdust by pulling the tool accordingly.

This improves work performance.

• The circular saw is recommended for cutting long

straight lines.

Sanding

CAUTION:

• Use sandpaper that has been used to sand metal,

not wood.

• Do not use worn sandpaper or sandpaper without

grit. Bring the sandpaper into contact with the work-

piece.

NOTE:

• A grinding sample on a test material is recommend-

ed in order to determine the pendulum stroke num-

ber suitable for your work.

• Use sandpaper with the same grain size until sand-

ing of the whole workpiece is nished. If the sand-

paper grain size is changed during work, a ne sur-

face nish may not be obtained.

13. Cleaning

Danger!

Always pull out the battery pack before starting any

cleaning work.

Cleaning

• Keep all safety devices, air vents and the motor

housing free of dirt and dust as far as possible.

Wipe the equipment with a clean cloth or blow it

with compressed air at low pressure.

• We recommend that you clean the device immedi-

ately each time you have nished using it.

• Clean the equipment regularly with a moist cloth

and some soft soap. Do not use cleaning agents

or solvents; these could attack the plastic parts of

the equipment. Ensure that no water can seep into

the device. The ingress of water into an electric tool

increases the risk of an electric shock.

14. Storage

Store the device and its accessories in a dark, dry

and frost-proof place that is inaccessible to children.

The optimum storage temperature is between 5 and

30˚C. Store the electrical tool in its original packag-

ing. Cover the electrical tool in order to protect it from

dust and moisture. Store the operating manual with

the electrical tool.

15. Maintenance

There are no parts inside the equipment which re-

quire additional maintenance.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Scheppach CMT200-20ProS Seite 22

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info