Bedienungsanleitung Scheppach CSE2400 (Seite 29 von 108) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Spanisch, Polnisch)

781698

Zoom out

Zoom in

Vorherige Seite

1/108

Nächste Seite

29GB

Then assemble the guide bar with the saw chain as

follows:

• Place the guide bar with the saw chain on the chain

wheel (16) and guide bolt (17). Ensure that the

adjustment plate (Fig.3/7A) is showing to you.

• Place the saw chain round the chain wheel (16).

Cause the chainsaw to the sprocket and check

whether it is correctly.

• The adjustment plate (7a) is fastened to the guide

rail (7) with the screw F.

• Place the cover (6) on top and tighten gently with

the lock nut (5).

Now the saw chain has to be correctly tensioned.

Tensioning the saw chain

Warning!

Always pull the plug out of the power socket before

doing any work on the chainsaw!

Wear safety gloves!

• Make sure the saw chain (4) is inside the guide

groove of the guide bar (7).

• Turn the outer Knob (Fig. 3/5A) clockwise until

the saw chain is correctly tensioned, then rotate

the inside knob (5) to block the guide bar in that

position.

• While the inside knob is being tightened, the guide

bar must then be pushed upwards.

• Check the chain tension again. Do not tension the

chain too tightly.

• When cold, it should be possible to lift the chain in

the middle of the guide bar approx. 5 mm. Tighten

the lock nut (5) securely.

• When warm, the saw chain will expand and slacken

and there is a danger of it jumping off the rail

altogether. Re-tension if necessary.

• If the saw chain is re-tensioned when hot, it must

be loosened again when the sawing work has been

completed.

• Otherwise, the contraction which takes place as the

chain cools would result in excessively high tension.

• A new saw chain requires a running-in period of

approx .5 minutes. Chain lubrication is very

important at this stage. After running in, check

chain tension and re-tension if necessary.

9. Working instructions

Transporting the chainsaw

Before transporting the chainsaw, always remove

the plug from the power socket and slide the chain

guard over the rail and chain. If several cuts are to

be performed with the chain saw, the saw must be

switched off between cuts.

Securing the extension lead

Only use extension leads suitable for outdoor use. The cross

section of the cable (max. length of extension cord: 75m)

must be at least 2,5 mm². secure the chainsaw ex to the

extension lead by inserting the extension lead into the strain

relief gap of the housing (Fig..M).Extension leads longer

than 30 m will reduce the performance of the chainsaw.

Chain lubrication

To prevent excessive wear, the saw chain and guide

bar must be evenly lubricated during operation.

Lubrication is automatic. Never work without chain

lubrication. If the chain runs dry, the entire cutting

apparatus will quickly become severely damaged.

It is therefore important to check both chain lubrica-

tion and the oil gauge every use (Fig. 4).

Never use the saw when the oil level is below the

“Min.” mark.

• Min.: When only approx. 5 mm of oil is visible

at the lower rim of the oil gauge (15), you must

top up with oil.

• Max.: Top up with oil until the window is full.

Chain lubricants

The service life of saw chains and guide bars depends

to a large extent on the quality of the lubricant used.

Old oil must not be used! Use only environment-

friendly chain lubricant. Store chain lubricant only in

containers which comply with the regulations.

Guide bar

The guide bar (7) is subjected to especially severe

wear and tear at the nose and the bottom. To avoid

one-sided wear and tear, turn the guide bar over

every time when you sharpen the chain.

Chain wheel

The chain wheel (16) is subjected to especially high

wear and tear. If you notice deep wear marks on

the teeth, the chain wheel must be replaced. A worn

chain wheel curtails the service life of the saw chain.

Have the chain wheel replaced by a specialist dealer

or your Customer Service.

Chain guard

The chain guard must be clipped onto the chain

and sword as soon as the sawing work has been

completed and whenever the chainsaw has to be

transported.

Chain brake

In the event of kick-back, the chain brake (3) will be

actuated via the front nger guard. The front nger

guard is pushed forwards by the back of the hand

and this causes the chain brake to stop the chain

saw, or rather the motor, within 0.15 s (Fig 5, H).

Releasing the chain brake (Fig 5)

To be able to use your chain saw again, you must

release the saw chain again. First switch off the

chainsaw. Then push the front nger guard (3) back

into the vertical position until it locks in place (Fig

5, I). The chain brake is now fully functional again.

Chainsaw protection

Never use the chainsaw in the rain or in damp

conditions.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Scheppach CSE2400 Seite 29

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info