Bedienungsanleitung Scheppach CSE2500 (Seite 29 von 200) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Spanisch, Polnisch)

781410

Zoom out

Zoom in

Vorherige Seite

1/200

Nächste Seite

 www.scheppach.com /  service@scheppach.com /  +(49)-08223-4002-99 /  +(49)-08223-4002-58

GB | 29

• Use a surge protector with a release current of

30 mA or less.

• Have your power tool serviced by a qualied repair

person using only identical replacement parts.

• Carefully follow the maintenance, control and ser-

vice instructions in this manual.

• Practise using the saw (sawing logs on a saw-

horse) and get an experienced user or a specialist

to explain to you the function of the saw, the way of

working, the techniques of sawing and the personal

protection equipment.

6. Technical data

Cutting data chainsaw

Cutting lenght 45,5 cm

Bar lenght 45,7 v

Capacity oiltank 0,125 l

Type of oil wear resistant oil

Saw chain division 3/8"

Drive link thickness 1,27 mm

Saw chain type Oregon

91PX062X

Number of teeths drive

sprocket 6

Tooth pitch of drive sprocket 3/8"

Chain brake yes

Guide bar type Oregon

180SDEA041

Engine

Motor 230-240 V / 50 Hz

Power 2400 W

Cutting speed max. 14 m/s

Weight 5,5 kg

Weight without bar and chain 4,8 kg

Subject to technical changes!

Information concerning noise emission measured

according to relevant standards:

Sound pressure LpA = 93 dB(A)

Sound power LWA = 104,6 dB(A)

Guaranteed Sound power LWA = 106 dB(A)

Uncertainty KPA = 3 dB(A)

Wear ear-muffs.

The impact of noise can cause damage to hearing.

Vibration Ahv (front handle) = 7,5 m/s2

Vibration Ahv (rear handle) = 7,5 m/s2

Uncertainty KPA = 1,5 m/s2

• The specied vibration emission value has been

measured according to a standardised testing pro-

cedure and can be used for comparison of one

electric tool with another;

• The specied vibration emission value can also be

used for an initial assessment of the load.

Warning:

• The vibration emission value can vary from the

specied value during the actual use of the elec-

tric tool, depending on the type and the manner in

which the electric tool is used;

• Try to minimise stress from vibrations as low as

possible. Some examples of means for reducing

the vibration stress are wearing gloves while us-

ing the tool and limiting work time. In the process

all parts of the operating cycle must be taken into

account (such as times in which the electric tool is

switched off or time in which it is switched on, but is

not running under a load).

7. Attachment and operation

Warning!

Always wear safety goggles, ear muffs, protective

gloves and heavy-duty work clothes! Use the saw

only with approved extension cables with the pre-

scribed insulation and connections designed for out-

door use (approved rubber-sheathed cables) which t

the chainsaw plug.

The chain saw is equipped with safety switches, re-

quiring the use of both hand. The chainsaw works

only when one hand is pushing the button 11 and 13

at the same time. If the chainsaw does not run, the

chain brake must be released at the front nger guard

(3). Be sure to read the sections “Chain brake” and

“Releasing the chain brake “ on this point.

To switch on:

• Release the chain brake (3), push in the lock (11)

and press the power switch (13).

• Place the lowest claw (Fig 2, J) on the wood . Raise

the chain saw by the rear grip (1 ) and saw into the

wood. Move the chain saw back a little and place

the claw further down.

• Be careful when sawing splintered wood as pieces

of wood may be ripped off.

After switching on, the chainsaw will run immediately

at high speed .

To switch off

• Release either the ON/OFF switch (13) on the rear

grip.

• The release of ON/OFF switch results the stop of

the chainsaw within 1sec., and heavy sparkling.

This is normal and safe for the proper operation of

the chainsaw.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Scheppach CSE2500 Seite 29

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info