www.scheppach.com / service@scheppach.com / +(49)-08223-4002-99 / +(49)-08223-4002-58
46 | GB
9. Cleaning
m WARNING
Disconnect the spark plug boot before doing any
cleaning and maintenance work. (Fig. 19)
Cleaning
• Keep all safety devices, air vents and the motor-
housing free of dirt and dust as far as possible.
Wipe the equipment with a clean cloth or blow
it with compressed air at low pressure. ATTEN-
TION! Wear safety glasses!
• We recommend that you clean the device immedi-
ately each time you have nished using it.
• Clean the equipment regularly with a moist cloth
and some soft soap. Do not use cleaning agents
or solvents; these could attack the plastic parts
of the equipment. Ensure that no water can seep
into the device.
10. Maintenance
Air lter (Fig.16-18)
• Clean the air lter (H) after each use.
• Unscrew the air lter mounting nut (Fig.18/Pos.6)
and remove the cover. (see Fig.16)
• Remove the air lter (H).
• Open the air lter with a screwdriver.
• Clean the air lter. Wash the lter in clean, warm,
soapy water. Let the air dry completely.
• Insert the air lter. Put on the cover of the engine /
air lter. Make sure the cover is installed correctly
(S-V). Tighten the screw that secures the cover.
(see Fig.16)
m NOTE
It is advisable to keep a stock of spare lters.
Oil supply opening (Fig.20)
• Check the oil supply opening (K) after each use.
• Dissemble the bar.
• Check the oil outlet (K) for obstructions.
Guide bar (Fig.23-24)
• Clean the bar after each use.
• Remove the bar from the machine.
• Remove sawdust from the bar and the oil channel
(Fig.23/Pos.1).
• Lubricate the teeth (Fig.24/Pos.2/3) through the
oiling hole with an oil syringe.
Cylinder ns (Fig.20)
• Clean the cylinder ns (M) after each use. To do
this, use compressed air at low pressure or use a
brush. ATTENTION! Wear safety glasses!
8. Operation
Start the appliance (Fig.10-13)
m CAUTION!: Before you start the engine, make
sure that the chain isn’t touching anything and
the chain brake is activated before each start.
1. Set the power switch (11) to position „ON“.
(Fig.10/Pos.11a)
2. Pull the choke lever (7) out completely until it
locks in place.
3. Press the fuel pump ball (6) 10 times (g. 2)
m NOTE
When restarting immediately after stopping the en-
gine, do not pull out the CHOKE (7).
4. Press the front handle (3) forward to activate the
chain brake
5. Place the saw on a rm, level surface. Hold the
saw rmly with the foot as indicated. Quickly pull
the starter (13) 2 times. Pay attention to the
running chain!
6. Once the engine has started, press the throttle
trigger lock (8) and the throttle lever (10) so that
the CHOKE knob (7) clicks into place again.
7. Pull the front handle (3) backwards to release the
chain brake.
8. Let the engine warm up, controlling the throttle
setting (10) and letting the chain run briey.
Never start or operate the chainsaw if the chain and
the chain brake lever or the front hand guard have
not been properly installed. In addition, always start
with the chain brake active. Proceed as follows for
this:
• Hold the chain saw by the front handle (4).
• Press the front hand guard (3) forward to position
(3b). Press the pedal, the chain should not move.
• Pull the front handle (3) back to position (3a). Press
the pedal, the chain should move.
Stopping the motor (Fig.10)
1. Release the throttle lever and wait until the en-
gine is idling.
2. Set the power switch to „Stop (0)“ to stop the mo-
tor. (Fig.10/Pos.11b)
m NOTE
To stop the engine in an emergency, activate the
chain brake and set the ON / OFF switch to „Stop“.
