Bedienungsanleitung Scheppach DB2000 (Seite 21 von 36) (Deutsch, Englisch, Französisch)

781887

Zoom out

Zoom in

Vorherige Seite

1/36

Nächste Seite

 www.scheppach.com /  service@scheppach.com /  +(49)-08223-4002-99 /  +(49)-08223-4002-58

GB | 21

• Keep safety devices, air vents and the motor hous-

ing as dust and dirt-free as possible.

• Clean the device with a clean cloth, or blow it out

with compressed air at low pressure.

• All moving parts are to be re-greased at periodic

intervals.

• Do not use detergents or solvents as these might

damage the plastic parts of the device. Make sure

that no water can get inside the device.

Carbon brushes

In case of excessive sparking, have the carbon brush-

es checked by a qualied electrician.

m CAUTION! The carbon brushes should be re-

placed only by a qualied electrician.

Check the oil level

The oil level should be checked before each use of

the device.

Place the device with the tool holder in the down

position on the oor. The oil must be at least 4 mm

above the bottom edge of the sight glass. Rell oil, if

required.

Oil change (Fig. E)

The oil should be changed after about 40-50 hours

of operation.

Recommended oil: 30 ml SAE 15W/40 or similar.

m CAUTION! Switch off the device. Disconnect

the mains plug!

1. Unscrew the sight glass (4) using the Allen wrench

(4) and drain the oil.

2. To prevent uncontrolled drainage of oil, place the

container under the drain plug and collect the oil

in it.

Note: Waste oil must be disposed of at the appro-

priate collection point for used oil!

3. Fill the new oil has reached (about 30 ml) into the

oil ller opening, until the oil level has reached the

specied level.

4. Tighten the sight glass again.

5. Check the oil level again after a short period

Service information

Please note that the following parts of this product

are subject to normal or natural wear and that the fol-

lowing parts are therefore also required for use as

consumables.

Wear parts*: Chisel, carbon brushes

* Not necessarily included in the scope of delivery!

AC motor

• The mains voltage must be 230 V~ / 50 Hz

• Extension cables up to 25 m length must have a

cross section of 1.5 mm2.

Power supply and extension cord must be 3-wire = P

+ N + SL. - (1/N/PE).

The mains supply is secured up to 16 A.

• The product meets the requirements of EN 61000-

3-11 and is subject to special connection condi-

tions. This means that use of the product at any

freely selectable connection point is not allowed.

• Given unfavourable conditions in the power supply

the product can cause the voltage to uctuate tem-

porarily.

• The product is intended solely for use at connec-

tion points that

a) do not exceed a maximum permitted supply im-

pedance “Zmax”, or

b) have a continuous current-carrying capacity of

the mains of at least 100 A per phase.

• As the user, you are required to ensure, in consulta-

tion with your electric power company if necessary,

that the connection point at which you wish to oper-

ate the product meets one of the two requirements,

a) or b), named above..

Connections and repairs of electrical equipment may

only be carried out by an electrician.

Please provide the following information in the event

of any enquiries:

• Type of current for the motor

• Machine data - type plate

• Motor data - type plate

13. Maintenance

If personnel qualied for unusual maintenance tasks

or repairs must be obtained during of after the war-

ranty period, please always contact a service point

recommended by us or contact the manufacturer.

• Only perform repair, maintenance and cleaning

work as well as the correction of malfunctions with

the drive switched off as a basic rule.

• All protective and safety equipment must be reas-

sembled immediately after repair, maintenance is

completed.

Cleaning

m CAUTION! Disconnect the mains plug.

• Clean the machine each time after completing

work.

• The machine should be cleaned reg-

ularly to remove dust and dirt.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Scheppach DB2000 Seite 21

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info