Bedienungsanleitung Scheppach Deco-Tronic (Seite 11 von 92) (Alle Sprachen)

782187

Zoom out

Zoom in

Vorherige Seite

1/92

Nächste Seite

12 english

the bench and guide the saw blade pins into the recess.

Repeatthisprocedurefortheupperbladeholder.Push

the upper arm of the saw slightly downwards before

tighteningthescrews(Fig.9,10,13).

2Checkthepositions ofthe bladepins in both holders

(Fig.12).

3Tensionthebladeusingthetensioningtap.Checkthe

bladetension.Carryonturningclockwisetotensionthe

bladefurther(Fig.11).

Note: It is difﬁcult to open the tensioning tap again if the blade

is too tightly tensioned.

Basic operation

Ascrollsawisfundamentallya„curvecuttingtool“but

which can also carry out straight and angled edge cuts. Fa-

miliarise yourself with the following important points prior

to commissioning the saw.

• Thesawdoesnotautomaticallycutwood.Youmustfeed

the wood against the saw blade manually.

• ThecuttingprocessoccursonIywhilethebladeismov-

ing downwards.

• Feedthewoodslowlyagainstthesawbladeasthesaw

blade teeth are small and cut only while moving down-

wards.

• AlIpersonscarryingoutworkwiththesawrequiretrain-

ing. The saw blade may break easily during this train-

ing time Iwhile the operator is sti1l unfamiliar with the

saw.

• Thesawisbestsuitedtorsheetsofwoodlessthan2.5

cm thick.

• Feedthewoodespeciallyslowlyagainstthebladeand

avoid abrupt curves to prevent the saw blade from break-

ing, if you wish to cut wood sheets thickerthan 2.5 cm.

• Sawbladeteethbluntenovertime,sawbladesmustbe

replaced.Thesawbladesaresufcienttor1/2to2op-

erating time depending upon the type of wood.

• Tryandmakesurethatthesawbladefollowsthegrainof

the wood in order to obtain a clean cut.

• deco 402/decotronic: The saw speed must be reduced

to minimum when cutting precious and non-terrous met-

als.

Inside cuts

Warning: Switch off the saw and remove the mains supply plug

before installing saw blades in order to avoid injuries caused

by unintentional activation of the saw.

This saw is suited also to inside cuts cuts not starting at

the edge of the work piece. Proceed as follows:

• Drilla6mmholeintheworkpiece.

• Loosenthebladetensionerandreleasethetensionin

the blade.

• Placetheboreholeoverthesawbladeslotinthework

bench.

• Installthesawbladethroughtheholeintheworkpiece

and through the work blade slot, and fasten the blade to

the holders.

• Whenyouhavecompletedtheinsidecut,removethesaw

blade and then remove the workpiece from the bench.

m Electrical connection

The installed electric motor is completely wired ready for

operation.

The customer’s connection to the power supply system,

and any extension cables that may be used, must conform

with local regulations.

Important remark:

The motor is automatically switched off in the event of an

overload. The motor can be switched on again after a cool-

ing down period that can vary.

Defective electrical connection cables

Electrical connection cables often suffer insulation dam-

age.

Possible causes are:

• Pinch points when connection cables are run through

window or door gaps.

• Kinksresulting fromincorrect attachmentor layingof

the connection cable.

• Cutsresultingfromrunningovertheconnectingcable.

• Insulationdamageresultingfromforcefullypullingout

of the wall socket.

• Cracksthroughagingofinsulation.

Such defective electrical connection cables must not be

used as the insulation damage makes them extremely haz-

ardous.

Checkelectricalconnectioncablesregularlyfordamage.

Make sure the cable is disconnected from the mains when

checking.

Electrical connection cables must comply with the regula-

tions applicable in your country.

Single-phase motor

• Themainsvoltagemustcoincidewiththevoltagespeci-

edonthemotor’sratingplate.

• Extensioncablesuptoalengthof25mmusthavea

cross-section of 1.5 mm2, and beyond 25 m at least 2.5

mm2.

• Theconnectiontothemainsmustbeprotectedwitha

16 A slow-acting fuse.

Onlyaqualiedelectricianispermittedtoconnectthema-

chineandcompleterepairsonitselectricalequipment.

Intheeventofenquiriespleasespecifythefollowingda-

ta:

• Motormanufacturer

• Typeofcurrentofthemotor

• Datarecordedonthemachine’sratingplate

• Datarecordedontheswitch’sratingplate

If a motor has to be returned, it must always be dispatched

with the complete driving unit and switch.

m Maintenance

Warning: In the interests of operational safety, always switch

off the saw and remove the mains plug before carrying out

maintenance work.

General

Reapplicationofthewaxcoatingontheworkbenchmakes

feeding the workpiece to the blade easier.

Motor

The mains cable should be replaced immediately if pulled

out, cut or damaged in any other way.

Donotlubricatethemotorbearingsorinternalparts!

Saw arm bearings

Lubricate the saw arm bearings every 50 hours. Proceed

asfollows(Fig.14).

Scheppach Deco-Tronic Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info