Bedienungsanleitung Scheppach DECO-XL (Seite 20 von 132) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Polnisch, Finnisch)

781463

Zoom out

Zoom in

Vorherige Seite

1/132

Nächste Seite

20 GB

Blade guard assembly, Fig. 4

Install the blade guard to the holder as shown in the

diagram. Secure the screws with a nut and washer.

• Lift the saw onto the frame and base and push it

onto the workbench.

• Familiarize yourself with the saw operating ele-

ments and features.

Mounting the saw on a work bench, Fig. 5

• A workbench made from solid wood is betier than

one made of plywood, as interfering vibrations and

noise are more noticeable with plywood.

• The necessary tools and small parts for assem-

bling the saw on a workbench are not supplied

with the saw. However, use equipment of at least

the following size:

E Saw body

F Foam rubber base

GWork bench

H Flat seal

I Washer

J Hexagonal nut

K Lock nut

L Hexagonal bolt

Ouantity Description

4 Hexagonal bolts (6mm) 1/4-20 x length

4 Flat seal (7mm) 9/321.0

4 Washers (7mm) 9/321.0.

8 Hexagonal nuts (6 mm) 1/4-20

First of all, drill holes into the seating surface and

then insert the screws.

• A foam rubber base for reduction of noise is not

supplied with the saw either. However, we express-

ly recommend that you use such a base to keep

vibration and noise to a minimum. Ideal size 400

x 240 mm.

Changing the saw blades

Warning: Switch off the saw and remove the mains

supply plug before installing saw b!ades in order to

avoid injuries caused by unintentiona! activation of

the saw.

A. Flat saw-blades Fig. 6

Use the adapter with at saw-blades.

The saw-blade is xed with Allen screws.

A 1 Saw-blade removal, g. 7+8, 10

• Extract the saw-blade by sliding the table’s inlay

up, then unscrew the tightening screw (1).

• Slightly press the upper arm (M) down (g. 10).

• Then remove the sawblade by pulling it forward out

of the supports and through the access perfora-

tion in the table.

A 2 Inserting the saw-blade:

• Put the saw-blade with the two adapters into the

lower support, the other end into the upper sup-

port.

• Slightly press the upper arm (M) down (g 10) be-

fore hooking it in.

• Tighten the blade with the tightening screw (1)

(g.7) by rotating it clockwise. Check the tightness

of the blade. Keep on rotating clockwise in order

to tighten the blade even more.

B. Saw-blade with pins

B 1 Saw blade removal, g. 7 + 8

• Extract the saw-blade by rst unscrewing the tight-

ening screw (1).

• Remove the saw-blade from the upper and lower

support by slightly pressing the saw´s upper arm

down (g. 10, M).

B 2 Inserting the saw-blade g 7, 9-11

• Lead one end of the saw-blade through the per-

foration in the table and insert the saw-blade pins

into the notch. Repeat this procedure at the upper

blade support.

• Before hooking it in, slightly press the saw´s upper

arm down. (Fig 9; Nr. 10)

• Check the position of the blade pins at the sup-

ports (g 11).

• Tighten the blade by means of the tightening

screw. Check the blade´s tightness. Keep on ro-

tating clockwise in order to tighten the blade even

more. (Fig. 7).

8. Operation

A scroll saw is fundamentally a „curve cutting tool“

but which can also carry out straight and angled

edge cuts. Familiarise yourself with the following im-

portant points prior to commissioning the saw.

• The saw does not automatically cut wood. You

must feed the wood against the saw blade manu-

ally.

• The cutting process occurs on I y while the blade

is moving downwards.

• Feed the wood slowly against the saw blade as

the saw blade teeth are small and cut only while

moving downwards.

• AlI persons carrying out work with the saw require

training. The saw blade may break easily during

this training time Iwhile the operator is sti1l unfa-

miliar with the saw.

• The saw is best suited tor sheets of wood less than

2.5 cm thick.

• Feed the wood especially slowly against the blade

and avoid abrupt curves to prevent the saw blade

from breaking, if you wish to cut wood sheets thick-

erthan 2.5 cm.

• Saw blade teeth blunten over time, saw blades

must be replaced. The saw blades are sufcient

tor 1/2 to 2 operating time depending upon the

type of wood.

• Try and make sure that the saw blade follows the

grain of the wood in order to obtain a clean cut.

• The saw speed must be reduced to minimum when

cutting precious and non-terrous metals.

Inside cuts

Warning: Switch off the saw and remove the mains

supply plug before installing saw blades in order to

avoid injuries caused by unintentional activation of

the saw.

This saw is suited also to inside cuts cuts not starting

at the edge of the work piece. Proceed as follows:

• Drill a 6 mm hole in the work piece.

• Loosen the blade tension er and release the ten-

sion in the blade.

• Place the bore hole over the saw blade slot in the

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Scheppach DECO-XL Seite 20

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info