Bedienungsanleitung Scheppach DECO-XL (Seite 21 von 132) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Polnisch, Finnisch)

781463

Zoom out

Zoom in

Vorherige Seite

1/132

Nächste Seite

21GB

work bench.

• Install the saw blade through the hole in the work

piece and through the work blade slot, and fasten

the blade to the holders.

• When you have completed the inside cut, remove

the saw blade and then remove the workpiece from

the bench.

Foot switch / continuous operation (Fig. 1+12+13)

The machine can be operated in continuous opera-

tion or with the additional foot switch (9). The switch

(11) is used to select between the operating modes.

The operating mode should always be selected when

the machine is switched off.

The machine is in the foot switch mode when the

switch is at the "0" position.

The machine is in the continuous mode when the

switch is at the “I" position.

Attention! The machine may start due to unintentional

actuation of the foot switch in the foot switch mode.

Attention! Never leave the machine unattended while

it is switched on.

Switching on/off (Fig. 1+12)

It is possible to switch the saw on by pressing the

green "I" button (6).

In order to switch the saw off again, it is necessary to

press the red "0" button (6).

The red warning light (a) indicates whether the machine

is switched on or off. The machine is switched on when

this lights up. (The machine only starts up in the foot

switch mode once the pedal is actuated, the red warn-

ing light illuminates anyway.)

You can only switch between foot switch and continu-

ous operation when the red warning light is not illumi-

nated. If necessary, switch machine off rst by pressing

the red button “0” (6).

Make sure you are aware of what operating mode

(pedal/continuous operation) your machine is in before

switching it on.

Beware of unintentional actuation of the foot switch.

Set the pedal (9) on the ground. The machine can be

switched on/off in pedal mode when the pedal is actu-

ated. A foot switch for switching on/off is practical, espe-

cially for internal cuttings, since your hands are kept free

and you can fully concentrate on the work piece under

the scroll saw. However, it cannot inuence the speed.

With the continuously variable electronic speed control

(5), the cutting speed can be increased by turning to the

right or reduced by turning to the left.

Lighting system (8) (Fig.1+14)

The lighting system can be switched on by pressing the

switch (b) on the lamp.

The lighting system is switched off if the switch is

pressed again.

To change the batteries (2x AAA R03 1.5), open the

battery compartment on the bottom of the light by re-

moving the three screws (c) using a Phillips screwdriver.

Insert the new batteries. Dispose of the old batteries

properly.

Fit the cover of the battery compartment in reverse or-

der.

9. Maintenance

Warning: In the interests of operational safety, al-

ways switch off the saw and remove the mains plug

before carrying out maintenance work.

General

Wipe chips and dust off the machine from time to time

using a cloth.

Re-application of the wax coating on the workbench

makes feeding the workpiece to the blade easier.

Motor

The mains cable should be replaced immediately if

pulled out, cut or damaged in any other way.

Do not lubricate the motor bearings or internal parts!

Saw arm bearings

Lubricate the saw arm bearings every 50 hours. Pro-

ceed as follows (Fig. 15).

• Turn the saw to the side

• Apply a generous amount of SAE 20 oil to the shaft

end and bronze bearings.

• Let the lubricant oil work in overnight.

• Repeat the procedure the next day on the other

side of the saw.

There are no parts inside the equipment which re-

quire additional maintenance.

Special accessories

Pin saw blade-universal

135 x 2,0 x 0,25 Z 10

blade mm 1 set = 6 pieces, Article No. 8800 0011

Pin saw blade- wood/plastic mm

135 x 2,0 x 0,25 Z 7

1 set = 6 pieces, Article No. 8800 0012

Pin saw blade-wood mm

135 x 3,0 x 0,5 Z 4

1 set = 6 pieces, Article No. 8800 0013

10. Storage

Store the device and its accessories in a dark, dry

and frost-proof place that is inaccessible to children.

The optimum storage temperature is between 5 and

30˚C. Store the electrical tool in its original packag-

ing.

11. Electrical connection

The installed electric motor is completely wired ready

for operation.

The customer’s connection to the power supply sys-

tem, and any extension cables that may be used,

must conform with local regulations.

Important remark:

The motor is automatically switched off in the event

of an overload. The motor can be switched on again

after a cooling down period that can vary.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Scheppach DECO-XL Seite 21

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info