Bedienungsanleitung Scheppach Di1050 (Seite 16 von 56) (Deutsch, Englisch, Französisch, Polnisch)

782596

Zoom out

Zoom in

Vorherige Seite

1/56

Nächste Seite

 www.scheppach.com  service@scheppach.com  +(49)-08223-4002-99  +(49)-08223-4002-58

16 І GB

Switch position stage 1

Speed range: High torque, low speed

Switch position stage 2

Speed range: Low torque, high speed

Attention! Do not perform this setting during

drilling.

Preselecting the speed (Fig. 1)

1. The speed adjustment dial (9) allows you to dene

the maximum speed.

2. Set the speed adjustment dial (9) to the desired po-

sition.

3. If the on/off switch (10) is fully depressed, the motor

will still only turn as fast as the setting on the speed

adjustment dial (9).

4. This setting can also be adjusted during operation.

Set the direction of rotation (Fig. 1)

The device’s direction of rotation can be changed

with the rotational direction switch.

1. Wait for the device to shut-down.

2. Push the rotational direction speed (8) into the de-

sired position:

Clockwise rotation: to drill and screw in screws.

Anticlockwise rotation: to loosen screws.

Changeover drilling/impact drilling (Fig. 1)

1. Wait for the device to shut-down.

2. Set the changeover switch (1) to the “Drill” symbol.

3. Impact drilling: Set the changeover switch (1) to the

“Impact drill” symbol.

Practical tips

• Always use the proper tool.

• Immediately switch of the device, if the tool should

get jammed. Change the rotation direction to an-

ticlockwise rotation and the carefully unscrew the

jammed tool.

• Do not use any blunt or damaged tools or acces-

sories.

Electrical connection

The electrical motor installed is connected and

ready for operation. The connection complies

with the applicable VDE and DIN provisions.

The customer‘s mains connection as well as

the extension cable used must also comply with

these regulations.

Important information

In the event of an overloading the motor will switch

itself off. After a cool-down period (time varies) the

motor can be switched back on again.

Damaged electrical connection cable

The insulation on electrical connection cables is of-

ten damaged.

This may have the following causes:

The additional handle is equally suited for right and

left-handed person.

Mount/set depth stop (Fig. 4)

The boreholes can be precisely drilled to an exact

drilling depth x using the depth stop.

1. Press the depth stop release (4).

2. Use the depth stop (4) in the additional handle (7).

Make sure that the ute of the depth stop (4) en-

gages the ute of the additional handle (7).

3. Place the tip of the depth stop (3) to the desired

drilling depth x behind the tip of the drill.

4. Let go of the depth stop release (4). The depth stop

(3) is now locked.

5. Drill the hole until the depth stop (3) comes in con-

tact with the component part.

Inserting/replacing the tool (Fig. 1)

1. Open the keyless chuck (5) wide (RELEASE) so

that the tool can be inserted. To do so, rmly hold

the rear sleeve (5b) of the keyless chuck (5) and

turn the front sleeve (5a) in the anti-clockwise di-

rection.

2. Insert the tool as far as possible into the keyless

chuck (5).

3. Close the keyless chuck (5) (GRIP) in order to

clamp the tool. To do so, rmly hold the rear sleeve

(5b) of the keyless chuck (5) and turn the front

sleeve (5a) in the clockwise direction.

4. To remove the tool again, rotate the keyless chuck

(5) and pull out the tool.

Always use a universal bit holder use using a screw-

driver bits.

Operation

Do not use the device without the additional han-

dle. It provides additional hold and reduces the

risk of injury.

Observe noise control and local regulations.

Switching on and off (Fig. 1)

1. Connect the machine to the power supply. Make

sure that the net voltage matches the voltage rating

indicated on the device’s type plate. Switching on:

Press the on/off switch (10).

2. By using the on/off switch (10)) you can progres-

sively control the speed.

Gentle pressure: low speed

Increase pressure: higher speed.

3. Continuous operation: Press the lock button (12).

The on/off switch (10)) is locked.

4. Switching off: Release the on/off switch (10). For

continuous operation, briey press the on/off switch

(10).

Dening the speed range (Fig. 1)

The gear selector switch (2) allows you to work within

a specic speed range.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Scheppach Di1050 Seite 16

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info