781655
20
Zoom out
Zoom in
Vorherige Seite
1/80
Nächste Seite
www.scheppach.com service@scheppach.com +(49)-08223-4002-99 +(49)-08223-4002-58
20 І 80
Removing the rack, Fig.4
In order to install your drill, you must rst remove the
rack (E)
1. Use an Allen key (WAF3) to remove the ring (F)
and pull this off the column (2).
2. Now pull the rack (F) out.
Pre-installing the drilling table holder, Fig.5+6
1. Push the crank holder (20) through the hole in the
drilling table holder (18) from the inside.
2. Put the crank handle (17) on the crank holder and
use the Allen key (3) to secure the crank handle
(17).
Installing the drilling table holder, Fig.7+8
1. Insert the rack (E) into the groove on the drilling
table holder (18).
2. Align the rack (E) centrally in relation to the drilling
table holder (18).
3. When bringing the rack (E) together within the
groove, ensure that the tooth meshing between the
rack and the drilling table holder (18) is correct.
4. Now place the drilling table holder (18) with the
rack (E) on the column (2) and guide the rack (E)
into the bottom rack guide on the column foot.
5. Use the ring (F) to secure the rack (E). Ensure that
the rack guide on the ring (F) is pointing down-
wards. Tighten the integrated Allen screw to afx
the ring (F).
6. Screw one of the clamping handles (3) into the
drilling table holder (18).
Installing the drilling table, Fig.5
1. Insert the drilling table (4) into the drilling table
holder (18).
2. Use a clamping handle (3) to secure the drilling
table (4).
3. Insert the roller support (13) into the receptacle on
the drilling table (4) and use the wing screws (21)
to secure it.
Installing the machine head and column, Fig. 10
1. Place the machine head (14) on the column (2).
2. Align the drills spindle with the table and the base
plate and tighten the Allen screw that is located on
the side of the machine head. (Allen key WAF4 / C)
Installing the handles, Fig. 11+12
1. Screw three handles (10) tight in the handle
brackets thread. Use the hexagon spanner (A) to
do this.
2. Screw the remaining handle (10) into the handle
bracket for speed adjustment. Use the hexagon
spanner (A) to do this.
Installing the folding swarf protector and the drill
chuck, Fig.13
1. Push the folding swarf protector (11) onto the spin-
dle on the machine head and use a Phillips head
screwdriver to secure it.
2. Push the tapered mandrel (22) into the drill chuck
(12) with a sharp jolt.
3. Then push the tapered mandrel (22) into the drill
spindle. To do this, guide the drill chuck (12) includ-
ing the cone (22) into the spindle until is reaches
the stop and then turn it until it slides a little further
into the spindle. Now insert the drill chuck (12)
including the cone into the spindle. Check that it is
tight.
Important: All bare parts are greased in order to protect
them from corrosion. Before mounting the drill chuck
(12) onto the spindle, both parts must be completely
Technical Data
Nominal input voltage 230-240V~ 50Hz
Power rating 550W
Motor speed 1450min-1
Output speed (innitely adju-
stable) 440 - 2580 min-1
Drill chuck mount B16
Spindle taper MT2
Drill chuck 1 - 16mm
Dimensions of drill table 240 x 240mm
Angle adjustment of table 45° - 0° - 45°
Drill depth 80mm
Pillar diameter 65mm
Height 713mm
Weight 38.5kg
Laser class 2
Wavelength of laser 650mm
Laser output 1mW
Noise and vibration values
The total noise values determined in accordance with
EN 61029.
sound pressure level - no load LpA 70.2 dB(A)
sound pressure level - load LpA 73.5 dB(A)
uncertainty KpA 3 dB(A)
sound power level - no load LWA 82.7 dB(A)
sound power level - no LWA 86.3 dB(A)
uncertainty KWA 3 dB(A)
Wear hearing protection.
The effects of noise can cause a loss of hearing. Total
vibration values (vector sum - three directions) deter-
mined in accordance with EN 61029.
Vibration emission value ah = 1.7 m/s2
K uncertainty = 1,5 m/s2
The specied vibration value was established in
accordance with a standardized testing method. It may
change according to how the electric equipment is used
and may exceed the specied value in exceptional
circumstances.
The specied vibration value can be used to compare
the equipment with other electric power tools.
The specied vibration value can be used for initial
assessment of a harmful effect.
Assembly
Column and machine foot, Fig. 3
1. Set the machine foot (1) down on the ground or the
workbench.
2. Place the column (2) on the base plate so that the
holes on the column (2) align with the holes on the
base plate (1).
3. Screw the four hexagonal screws (19) to fasten the
column into the base plate and tighten them using
a hexagon spanner (A).
20

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Scheppach DP18VARIO wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info