Bedienungsanleitung Scheppach DP18VARIO (Seite 22 von 80) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Polnisch)

781655

Zoom out

Zoom in

Vorherige Seite

1/80

Nächste Seite

 www.scheppach.com  service@scheppach.com  +(49)-08223-4002-99  +(49)-08223-4002-58

22 І 80

• Cracks due to the insulation ageing.

Such damaged electrical connection cables must not

be used and are life-threatening due to the insulation

damage.

Check the electrical connection cables for damage regu-

larly. Make sure that the connection cable does not hang

on the power network during the inspection.

Electrical connection cables must comply with the ap-

plicable VDE and DIN provisions. Only use connection

cables with the marking „H05VV-F“.

The printing of the type designation on the connection

cable is mandatory.

AC motor

• The mains voltage must be 230 V~

• Extension cables up to 25 m long must have a

cross-section of 1.5 mm2.

Connections and repairs of electrical equipment may

only be carried out by an electrician.

Please provide the following information in the event of

any enquiries:

Type of current for the motor

• Machine data - type plate

Cleaning and Servicing

Pull the mains plug before any adjustments,

maintenance or repair.

m Have any work on the device that is not de-

scribed in this instruction guide performed by

a professional. Only use original parts. Allow

the device to cool off before any maintenance or

cleaning is undertaken. There is a risk of burning!

Always check the device before using it for obvi-

ous defects such as loose, worn or damaged parts,

correct the positioning of screws or other parts. Ex-

change the damaged parts.

Cleaning

Do not use any cleaning agents or solvents. Chemical

substances can etch the plastic parts of the device.

Never clean the device under running water.

• Thoroughly clean the device after every use.

• Clean the ventilation openings and the surface of

the device with a soft brush or cloth.

• Remove chips, dust and dirt with a vacuum cleaner

if necessary.

• Lubricate moving parts regularly.

• Do not allow lubricants to come into contact with

switches, V-belts, pulleys and drill lifting arms.

Storage

Store the device and its accessories in a dark, dry and

frost-proof place that is inaccessible to children. The

optimum storage temperature is between 5 and 30˚C.

Store the electrical tool in its original packaging.

Cover the electrical tool in order to protect it from dust

and moisture.

Store the operating manual with the electrical tool.

Working speeds

Ensure that you drill at the proper speed. Drill speed is

dependent on the diameter of the drill bit and the mate-

rial in question.

The table below acts as a guide for selecting the proper

speed for various materials.

Note: The drill speeds speci ed are merely sugges-

ted values.

Drill

bit Ø

Cast

iron

Steel Iron Alumi-

nium

Bronze

32550 1600 2230 9500 8000

41900 1200 1680 7200 6000

51530 955 1340 5700 4800

61270 800 1100 4800 4000

71090 680 960 4100 3400

8 960 600 840 3600 3000

9 850 530 740 3200 2650

10 765 480 670 2860 2400

11 700 435 610 2600 2170

12 640 400 560 2400 2000

13 590 370 515 2200 1840

14 545 340 480 2000 1700

16 480 300 420 1800 1500

18 425 265 370 1600 1300

20 380 240 335 1400 1200

22 350 220 305 1300 1100

25 305 190 270 1150 950

Countersinking and center-drilling

With this table drill, you can also countersink and center-

drill. Please observe that countersinking should be

performed at the lowest speed, while a high speed is

required for center-drilling.

Drilling wood

Please note that sawdust must be properly evacuated

when working with wood, as it can pose a health hazard.

Ensure that you wear a suitable dust mask when perfor-

ming work that generates dust.

Electrical connection

The electrical motor installed is connected and

ready for operation. The connection complies with

the applicable VDE and DIN provisions.

The customer‘s mains connection as well as the

extension cable used must also comply with these

regulations.

Important information

In the event of an overloading the motor will switch

itself off. After a cool-down period (time varies) the mo-

tor can be switched back on again.

Damaged electrical connection cable

The insulation on electrical connection cables is often

damaged.

This may have the following causes:

• Passage points, where connection cables are

passed through windows or doors.

• Kinks where the connection cable has been improp-

erly fastened or routed.

• Places where the connection cables have been cut

due to being driven over.

• Insulation damage due to being ripped out of the

wall outlet.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Scheppach DP18VARIO Seite 22

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info