Bedienungsanleitung Scheppach DS1200 Primaster (Seite 21 von 36) (Deutsch, Englisch, Französisch)

782196

Zoom out

Zoom in

Vorherige Seite

1/36

Nächste Seite

General

Wipe chips and dust off the machine from time to time

using a cloth.

Re-application of the wax coating on the workbench

makes feeding the workpiece to the blade easier.

Motor

The mains cable should be replaced immediately if

pulled out, cut or damaged in any other way.

Do not lubricate the motor bearings or internal parts!

Saw arm bearings

Lubricate the saw arm bearings every 50 hours. Pro-

ceed as follows (Fig. 11).

• Turn the saw to the side

• Apply a generous amount of SAE 20 oil to the shaft

end and bronze bearings.

• Let the lubricant oil work in overnight.

• Repeat the procedure the next day on the other

side of the saw.

There are no parts inside the equipment which re-

quire additional maintenance.

Special accessories

Pin saw blade-universal

135 x 2,0 x 0,25 Z 10

blade mm 1 set = 6 pieces, Article No. 8800 0011

Pin saw blade- wood/plastic mm

135 x 2,0 x 0,25 Z 7

1 set = 6 pieces, Article No. 8800 0012

Pin saw blade-wood mm

135 x 3,0 x 0,5 Z 4

1 set = 6 pieces, Article No. 8800 0013

10. Storage

Store the device and its accessories in a dark, dry

and frost-proof place that is inaccessible to children.

The optimum storage temperature is between 5 and

30˚C. Store the electrical tool in its original packag-

ing.

11. Electrical connection

The installed electric motor is completely wired ready

for operation.

The customer’s connection to the power supply sys-

tem, and any extension cables that may be used,

must conform with local regulations.

Important remark:

The motor is automatically switched off in the event

of an overload. The motor can be switched on again

after a cooling down period that can vary.

Defective electrical connection cables

Electrical connection cables often suffer insulation

damage.

• Tighten the blade by means of the tightening

screw. Check the blade´s tightness. Keep on ro-

tating clockwise in order to tighten the blade even

more(Fig. 1).

8. Operation

A scroll saw is fundamentally a „curve cutting tool“

but which can also carry out straight and angled edge

cuts. Familiarise yourself with the following important

points prior to commissioning the saw.

• The saw does not automatically cut wood. You must

feed the wood against the saw blade manually.

• The cutting process occurs on I y while the blade

is moving downwards.

• Feed the wood slowly against the saw blade as the

saw blade teeth are small and cut only while mov-

ing downwards.

• AlI persons carrying out work with the saw require

training. The saw blade may break easily during

this training time Iwhile the operator is sti1l unfa-

miliar with the saw.

• The saw is best suited tor sheets of wood less than

2.5 cm thick.

• Feed the wood especially slowly against the blade

and avoid abrupt curves to prevent the saw blade

from breaking, if you wish to cut wood sheets thick-

erthan 2.5 cm.

• Saw blade teeth blunten over time, saw blades

must be replaced. The saw blades are sufcient

tor 1/2 to 2 operating time depending upon the type

of wood.

• Try and make sure that the saw blade follows the

grain of the wood in order to obtain a clean cut.

• The saw speed must be reduced to minimum when

cutting precious and non-terrous metals.

Inside cuts

Warning: Switch off the saw and remove the mains

supply plug before installing saw blades in order to

avoid injuries caused by unintentional activation of

the saw.

This saw is suited also to inside cuts cuts not starting

at the edge of the work piece. Proceed as follows:

• Drill a 6 mm hole in the work piece.

• Loosen the blade tension er and release the ten-

sion in the blade.

• Place the bore hole over the saw blade slot in the

work bench.

• Install the saw blade through the hole in the work

piece and through the work blade slot, and fasten

the blade to the holders.

• When you have completed the inside cut, remove

the saw blade and then remove the workpiece from

the bench.

9. Maintenance

Warning: In the interests of operational safety, always

switch off the saw and remove the mains plug before

carrying out maintenance work.

21 / 36

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Scheppach DS1200 Primaster Seite 21

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info