Bedienungsanleitung Scheppach DS1200 Primaster (Seite 20 von 36) (Deutsch, Englisch, Französisch)

782196

Zoom out

Zoom in

Vorherige Seite

1/36

Nächste Seite

• First of all, drill holes into the seating surface and

then insert the screws.

• A foam rubber base for reduction of noise is not

supplied with the saw either. However, we express-

ly recommend that you use such a base to keep

vibration and noise to a minimum. Ideal size 400

x 240 mm.

Changing the saw blades

Warning: Switch off the saw and remove the

mains supply plug before installing saw b!ades

in order to avoid injuries caused by unintentio-

na! activation of the saw. The teeth of the saw

blade must always point downwards.

A. Flat saw-blades Fig. 9

Use the adapter (P) with at saw-blades.

The distance results by the setting gauge (12).

The saw-blade is xed with Allen screws.

A.1 Saw-blade removal, Fig. 1 + 9+ 9.1 + 9.2 + 9.3

+ 9.4

• Extract the saw-blade by sliding the table’s inlay

up, then unscrew the tightening screw (1).

• Slightly press the upper arm (M) down (g. 9.1).

• Then remove the sawblade by pulling it forward out

of the supports and through the access perfora-

tion in the table.

A.2 Inserting the saw-blade, Fig. 1 + 9+ 9.1 + 9.2 +

9.3 + 9.4

• Put the saw-blade with the two adapters into the

lower support, the other end into the upper sup-

port.

• Slightly press the upper arm (M) down (Fig. 9.1)

before hooking it in.

• Tighten the blade with the tightening screw (1) by

rotating it clockwise. Check the tightness of the

blade. Keep on rotating clockwise in order to tight-

en the blade even more.

B. Saw-blade with pins

B.1 Saw blade removal, Fig. 1 + 10 + 10.1 + 10.2

+ 10.3

• Extract the saw-blade by sliding the table’s inlay

up, then unscrew the tightening screw (1).

• Remove the saw-blade from the upper and lower

support by slightly pressing the saw´s upper arm

down (Fig. 10, M).

B 2 Inserting the saw-blade Fig. 1 + 10 + 10.1 +

10.2 + 10.3

• Lead one end of the saw-blade through the per-

foration in the table and insert the saw-blade pins

into the notch. Repeat this procedure at the upper

blade support.

• Before hooking it in, slightly press the saw´s upper

arm down. (Fig 10)

• Check the position of the blade pins at the sup-

ports (Fig 10.1 + 10.2).

7. Installation

Setting the saw bench, Fig. 3

Setting the angle scale

• Release the star button and bring the saw bench

(Fig. 3, A) to a right angle (Fig. 3, B) in relation to

the saw blade.

• Use a 90° angle tc measure the right angle be-

tween the blade and the bench. The saw blade be

90° to the angle.

• Close the star button again when the distance be-

tween the blade and the 90° angle is at a minimum.

The bench should then be at 90° to the saw blade.

• Release the lock screw (Fig. 3, C) and bring the

indicator to the zero position. Fasten the screw.

Please note: the angle scale is a useful piece of

supplementary equip ment, but should not be used

for precision work. Use scrap wood for saw tests,

adjust the bench if neces sary.

Note: The bench should not be on the motor block,

this can cause undesireable noise.

Horizontal saw bench and diagonal cuts, Fig. 3+4

• The saw bench can be positioned into a 450 di-

agonal position or be left in the horizontal position.

• You can read off the approximate slope angle

by using the angle scale located under the work

bench. For more exact adjustment, use scrap wood

for some saw tests; adjust the bench if necessary.

Blade guard assembly and hold-down clamp, Fig.

5+6

• Assemble the workpiece holder (Fig. 5, A) to the

clamp (Fig. 5, B) as shown in the image. This must

be xed rst to the machine with the tommy screw

(Fig. 5, C).

• Secure the blade guard with the screw and nut.

Assembly of dust blower, Fig. 7

Screw the exi-hose into the opening provided and

tighten it hand-tight.

Mounting the saw on a work bench, Fig. 5

• A workbench made from solid wood is betier than

one made of plywood, as interfering vibrations and

noise are more noticeable with plywood.

• The necessary tools and small parts for assem-

bling the saw on a workbench are not supplied

with the saw. However, use equipment of at least

the following size:

1 Saw body

2 Foam rubber base

3 Work bench

4 Flat seal

5 Washer (7 mm)

6 Hexagonal nut (6 mm)

7 Lock nut (6 mm)

8 Hexagon head screws (6 mm)

20 / 36

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Scheppach DS1200 Primaster Seite 20

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info