Bedienungsanleitung Scheppach DTB250-20ProS (Seite 22 von 108) (Deutsch, Englisch, Französisch, Polnisch)

782592

Zoom out

Zoom in

Vorherige Seite

1/108

Nächste Seite

 www.scheppach.com /  service@scheppach.com /  +(49)-08223-4002-99 /  +(49)-08223-4002-58

22 | GB

Rotary switch for screwing / drilling / ham-

mer-drilling

Using the rotary switch for screwing / drilling / ham-

mer-drilling (10), it is possible to choose between dif-

ferent operating modes.

• For screwing, turn the rotary switch to switch set-

ting A.

• For drilling, turn the rotary switch to switch setting B.

• For hammer-drilling, turn the rotary switch to switch

setting C.

Caution! Only move the rotary switch for screwing /

drilling / hammer-drilling (10) when the device is at a

standstill. Otherwise, there is a risk of damaging the

device.

Installation

Switching On /Off

Switching on:

To start the appliance squeeze on the ON / OFF switch

(3) and then keep it pressed down. The LED working

light (7) comes on with a slightly or fully pressed ON /

OFF switch (3) and illuminates the working area in

poor lighting conditions.

Switching off:

To stop the appliance, release the ON / OFF switch (3).

Adjusting the speed

The ON / OFF switch (3) has a variable speed control

device. Slight pressure on the ON / OFF switch (3)

will cause the rotation speed to slow down. With in-

creased pressure, the rotational speed will increase.

Note: The integrated engine brake means that the

device will come to a fast standstill.

Switching direction of rotation

To switch the direction of rotation, push the direction

of rotation switch (2) to either the right or to the left.

Tips and Tricks

Before you use the appliance, check to see that the

screw or drill bit is properly tted, i.e. located centrally

in the chuck. Screw bits are designated with their di-

mensions and their shape. If you are unsure, always

try the particular screw bit out to see whether it sits in

the screw head without any free play.

Torque:

Smaller screws and bits in particular can be easily

damaged if you adjust the appliance with too high a

torque and/or rotation speed.

Hard screwdriving conditions (into metal):

Particularly high torques can occur, for example with

metal screws tightened by socket tool bits. Select a

lower rotation speed.

Soft screwdriving conditions (e.g. into soft

wood):

You should also select a low speed in order not to

damage the wood workpiece surface through contact

with the metal screw head.

Use a countersinker.

When drilling into wood, metal and other materials, take

note of the following advice: With small diameter drill

bits use a high drill speed. For large diameter drill bits,

use a low drill speed. For hard materials, select a low

drill speed. For soft materials, select a high drill speed.

Secure or x down the workpiece (if possible) in a

clamp or vice.

Mark the intended position of the hole with a centre

punch or a nail and select a low drill speed for drilling.

Take the rotating drill bit out of the hole frequently so

that swarf or drill dust can be re-moved and the hole

and tool is ventilated.

Drilling in metal:

Use a metal drill bit (HSS). For the best results, you

should cool the bit with oil.

Metal drill bits can also be used to drill into plastic.

Drilling in stone:

Use a circular shafted masonry drill bit with a hard-

ened metal tip.

Drilling in wood:

Normally you should use a wood drill with a cen-

tring point. For deep holes, use an auger type bit.

For large diameter holes, use a forstner bit. You can

screw small screws into soft wood without the need

for pre-drilling.

12. Cleaning

Danger!

Always pull out the battery pack before starting any

cleaning work.

• Keep all safety devices, air vents and the motor

housing free of dirt and dust as far as possible.

Wipe the equipment with a clean cloth or blow it

with compressed air at low pressure.

• We recommend that you clean the device immedi-

ately each time you have nished using it.

• Clean the equipment regularly with a moist cloth

and some soft soap. Do not use cleaning agents

or solvents; these could attack the plastic parts of

the equipment. Ensure that no water can seep into

the device. The ingress of water into an electric tool

increases the risk of an electric shock.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Scheppach DTB250-20ProS Seite 22

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info