Bedienungsanleitung Scheppach FORSA 4.1 (Seite 33 von 44) (Deutsch, Englisch)

781492

Zoom out

Zoom in

Vorherige Seite

1/44

Nächste Seite

english 33

Maintenance

Switch off the motor and disconnect the power supply plug

before doing any maintence and cleaning work. Follow the

following maintenance procedures for your panel sizing circular

saw.

• Check belt tension after approx. 20 operating hour and

tighten if necessary. To do this open the right side cover.

Set required belt tension by adjusting the fastening nuts

on the motor equally.

• Spray the roller chain and moving parts (vertical and

swivel adjustment units) occasionally with dry lubricating

spray. Open the right side cover.

• Check the sliding table carriage guide unit for dirt and

clean if required.

• Always keep the table surface free of resin.

• If a dust extractor is not being used the saw blade

protective cover should be cleaned occassionally of any

wood residue and sawdust. This is important for ensuring

troublefree ejection of sawdust. If the machine is used

without a dust extractor sawdust accumulation could

reduce the vertical and angle adjustment range.

• Clean the sliding table carriage guide at regular intervals.

All safety equipment and protective devices must be reattached

as soon as repair and maintenance work has been completed.

• To ensure troublefree ejection of sawdust the saw blade

protective cover should be cleaned of any wood residue.

• T h e vertical and angle adjustment range could

b e reduced if sawdust is allowed to accumulate.

Open the protective cover and clean the adjustment

area.

Electrical Connection

The built in electric motor is wired ready for operation. The

connection conforms with the applicable VDE and DIN

regulations.

The mains connection on site and the extension cable used

should also comply with these regulations.

Motor Brake Device

Your panel sizing circular saw is equipped with an automatic

shutdown brake. The brake starts to take effect after the

driving motor switches off.

The saw blade must stop max.10 sec after switching off. Check

daily!

Do not operate the machine after a longer braking time.

Important Information

The 230 V / 50 Hz and 400 V / 50 Hz electric motors are

designed for S6 40 % operating mode.

If the motor starts to overload it switches off automatically. The

motor can reactivated after a cooling period (exact interval

differs).

Faulty Electric Connection Cables

Electric connection cables are frequently subjected to

insulation damage.

Insulation damage results from:

• Pinch points where connection cables are routed through

windows or door cracks.

• Kinks due to improper fastening or routing of connection

cables.

• Cuts caused by running over connection cords.

• Insulation damage caused by pulling the cable out of the

wall socket.

• Cracks due to aging.

Faulty or damaged electric connection cables are hazardous

and should not be used under any circumstances as fatal

injury could result.

Check electric connection cables regularly for damage.

Before you check the connection cable, make sure that it

has been completely disconnected from the power supply.

Electric connection cables must conform to the applicable

VDE and DIN regulations. Use only connection cables

2-3mm

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Scheppach FORSA 4.1 Seite 33

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info