Bedienungsanleitung Scheppach FORSA 4.1 (Seite 34 von 44) (Deutsch, Englisch)

781492

Zoom out

Zoom in

Vorherige Seite

1/44

Nächste Seite

34 english

Fault Possible Cause Remedy

saw blade detachs after motor is switched off fastening nut too slack tighten M 20 left-handed fastening nut

motor fails to start a) mains fuse outage a) check mains fuse

b) faulty extension cable b)

refer to section on electrical connection, in the

operating instructions

c) faulty connections to motor or switch, brake

fails to release

c) should be checked by a qualified electrician

d) faulty motor or switch d)

see section on electrical connection, in the

operating instructions

e) saw blade protective cover open e) close saw blade protective cover

incorrect motor rotational direction a) faulty capacitor a) should be replaced by a qualified electrician

b) incorrect connection b) wall socket polarity should be changed by a

qualified electrician

no motor output, motor switches off automati-

cally

a) overload caused by dull saw blade a) install sharpened saw blade

b) thermal protection activates b) can be switched on again after cooling

period

burn marks where cut is made

on cross section

a) dull saw blade a) install sharpened saw blade

b) incorrect saw blade b) install saw blade for lengthwise cuts

c) fence not parallel to saw blade c) replace fence

d) sliding table carriage not parallel to saw

blade

d) align sliding table carriage to saw blade

reduced saw performance at full motor speed loose belt tighten belt, refer to maintenance section

workpiece jams between sawblade and fence fence does not run parallel to saw blade check fence alignment

sliding table carriage does not move a) lock has not been released a) release lock

b) guide unit is dirty b) clean guide unit

marked as H 07 RN.

Regulations require that the type designation be printed on

the connection cable.

AC Motor

• The required supply voltage is 230 Volt - 50 Hz.

• Extension cables up to 25 m in length must have a cross

section of 1.5 mm2; extension cables which exceed 25

m in length must have a cross section of 2.5 mm2.

• The mains connection has a 16 A time delay fuse.

Three-Phase Current Motor

The 400 V / 50 Hz electric motor is designed for the S6 / 40 %

operating mode.

• The required supply voltage is 400 Volt - 50 Hz.

• The mains connection and extension cable must be

equipped with 5 wires = 3 P + N + PE.

• Extension cables must have a cross section of no less

than 1.5 mm2.

• The mains connection is fused to a maximum of 16 A.

• Check the rotational direction when connecting to the

power supply or changing location: it may be necessary

to change the polarity (wall socket).

If you have questions always provide the following information:

• motor manufacturer

• type of current used by motor

• data listed on the machine type plate

If you return the motor always send the complete drive unit

including switch.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Scheppach FORSA 4.1 Seite 34

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info