Bedienungsanleitung Scheppach FS850 (Seite 24 von 92) (Deutsch, Englisch, Französisch, Polnisch)

781905

Zoom out

Zoom in

Vorherige Seite

1/92

Nächste Seite

 www.scheppach.com /  service@scheppach.com /  +(49)-08223-4002-99 /  +(49)-08223-4002-58

24 | GB

Caution: Cutting disc must always be cooled with

water.

Caution: Cutting disc runs with a time lag.

Do not break the cutting disc by applying pressure at

the sides.

• Under normal use conditions, the motor casing can

become hot.

• Do not use force on the machine or on an acces-

sory to achieve the performance of a bigger Indus-

trial machine. It does a better job at the output for

which it is designed.

• Dene all machine settings only when it is switched

o󰀨.

• Do not leave the machine unattended as long as

it is running.

• During shut down, leave the machine only after it

comes to a complete standstill.

• Always switch the machine o󰀨 before pulling out

the power plug from the mains socket.

• Always pull out the power plug. Never disconnect

the power plug from the mains socket by pulling

at the cable.

• Do not use cutting discs that do not meet the size

specications.

• Do not carry the machine by the cable.

Do not work with the machine if you are not sure

whether a working condition is safe of unsafe.

90° cuts Fig.6-7

1. Loosen the wing bolt (C)

2. Set angled stop (6) to 90° and tighten the wing

bolt (C) again.

3. Tighten the wing bolt (D) to x the angled stop (6).

(Fig.6)

4. Push the machine head (1) towards the rear by

the handle (11).

5. Place the tile on the stop rail (7) at the angled stop

(6).

6. Switch the tile-cutting machine on. (Fig.7)

Caution: Wait for the cooling water to reach

the cutting disc (10).

7. Pull the machine head (1) slowly and uniformly by

the handle (11) in the forward direction through

the tile.

8. Switch the tile-cutter o󰀨 again after reaching the

end.

45° diagonal cut (Fig. 8)

1. Set the angled stop (6) to 45°

2. Perform cutting as described above.

45° longitudinal cut (Fig. 9)

1. Loosen the star knob screw (E) on both sides

2. Angle the guide rails (8) 45° to the left on the an-

gle scale (17).

3. Re-tighten the star knob screw (E) on both sides.

4. Perform cutting as described.

Residual risks can be minimized if the „safety in-

structions“ and the „proper use“, as well as operating

instructions manual are observed jointly.

Please note that our equipment has not been de-

signed for use in commercial, trade or industrial

applications. Our warranty will be voided if the equip-

ment is used in commercial, trade or industrial busi-

nesses or for equivalent purposes.

Any use beyond the one specied will be treated

as improper. The manufacturer will not be liable for

damages resulting from such improper use; the risk

will be borne by the user alone.

10. Installation

m IMPORTANT!

You must fully assemble the appliance before

using it for the rst time!

Replace cracked diamond cutting discs.

• Get to know your machine. Familiarize yourself

with its use and its restrictions, but also with the

specic potential risks.

• Check the machine carefully for damages to en-

sure that it is able to achieve the intended output.

In case of doubt, please replace the concerned

component.

• Ensure that the switch is on O󰀨, before inserting

the power plug into the mains socket.

• Ensure that the machine is cleaned and lubricat-

ed properly.

• Before start-up, check the machine for damaged

parts and nd out whether these parts are work-

ing properly and performing their dened function.

• Check the alignment of all moving parts, all bro-

ken or fastening parts, and all other conditions that

can a󰀨ect smooth operation. Each damaged part

should be repaired or replaced by a technician im-

mediately.

• Do not use the machine if a switch cannot be ac-

tivated/deactivated correctly.

On/O󰀨 switch (Fig. 4)

To switch on, press “I” on the On/O󰀨 switch (16) Be-

fore starting the cutting process, wait until the cutting

wheel reaches its maximum speed and the cooling

water pump (14) has fed the water to the cutting

wheel. To switch o󰀨, press the “0” on the switch (16).

(Fig. 4).

Operation

• Install the machine on an even, slide-proof oor.

• Check that the voltage on the nameplate matches

the existing voltage; connect the power plug to the

mains power supply only thereafter

• The cutting disc should be free to run before the

machine is switched on.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Scheppach FS850 Seite 24

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info