Bedienungsanleitung Scheppach HBS261 (Seite 29 von 176) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Polnisch)

781470

Zoom out

Zoom in

Vorherige Seite

1/176

Nächste Seite

 www.scheppach.com /  service@scheppach.com /  +(49)-08223-4002-99 /  +(49)-08223-4002-58

GB | 29

• 

-

ter a power failure.

•         

check that the voltage marked on the rating plate



• 

󰀨

• Persons working on the machine should not be

distracted.

• Note the direction of rotation of the motor and

blade.

• 

put them out of operation.

• Never cut workpieces which are too small to hold



• Never remove loose splinters, chips or jammed

pieces of wood when the saw blade is running.

• It is imperative to observe the accident prevention





• -

al associations.

• Adjustable protective devices have to be adjusted

as close as possible to the workpiece.

• Important! Support long workpieces (e.g. with a

roller table) to prevent them sagging at the end

of a cut.

• Make sure the blade guard (3) is in its lower posi-

tion when the saw is being transported.

• -

use the machine.

• 

must not be used.

• If the table insert is worn, replace it.

• Never operate the machine if either the door pro-



are open.

• Ensure that the choice of blade and the selected

speed are suitable for the material to be cut.

• Do not begin cleaning the blade until it has come

to a complete standstill.

• For straight cuts of small workpieces against the

longitudinal limit stop the push stick has to be

used.

• The bandsaw blade guard should be in its lowest

position close to the bench during transport.

• For miter cuts when the table is tilted, the paral-

lel stop must be positioned on the lower part of

the table.

• When cutting round timber, use a suitable holding

device to prevent the workpiece turning.

• Never use guards to lift or transport items.

• Ensure that the bandsaw blade guards are used



• 

bandsaw blade. Use a push stick for narrow cuts.

• The push stick has to be stored on the intended de-

vice, so that it can be reached from normal working



• In the normal operating position the operator is in

front of the machine.

• When sawing wood, connect the band saw to a

dust collection device.

•  

use a suitable holding device that prevents the

workpiece from twisting.

6. Technical data

Electro motor 220 - 240 V ~, 50 Hz

Power 550 W (S2 20 min)

Revolutions 1400 min-1

Saw band length 1790 mm

Saw band width 6 mm

Saw band width max. 13 mm

Saw band speed I 660 m/min

Saw band speed II 960 m/min

 0 - 120 mm

Opening width 245 mm

Table size 300 x 300 mm

Slewing range of the table 0° - 45°

size of workpiece max. 580 x 400 x 120 mm

Weight 24 kg

The work piece must have a minimum height of 3 mm

and a minimum width of 10 mm.



Operation at constant load for 20 minutes or less, fol-

󰀩

duration to re-establish machine temperatures within

2 K of the ambient temperature.

The total noise values determined in accordance

with EN 61029.

sound pressure level LpA 77,4 dB(A)

pA 3 dB

sound power level LWA 90,4 dB(A)

WA 3 dB

Wear hearing protection.

 󰀨     

Total vibration values (vector sum - three directions)

determined in accordance with EN 61029.

Scheppach HBS261 Seite 29

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info