Bedienungsanleitung Scheppach HD15 (Seite 19 von 120) (Alle Sprachen)

781454

Zoom out

Zoom in

Vorherige Seite

1/120

Nächste Seite

 www.scheppach.com /  service@scheppach.com /  +(49)-08223-4002-99 /  +(49)-08223-4002-58

19 / 120

• Remaining hazards can be minimized by following

the instructions in “Safety Precautions”, “Proper

Use“ and in the entire operating manual.

Keep this safety information in a safe place.

6. Technical data

Technical Data

Dimensions L x W x H

(mm): 1075 x 680 x 1800

Overall height with

lter bag mm 1800

Ectractor duct

connections ø mm 140

Hose length mm 2000

Approx. weight kg 44

Rate of air ow m3/h 2000

Pressure differential

Pa 1600

Filter aera (lter bag)

m2 ca. 1,6

Sawdust bag capacity

litres 130

Performance

Electric motor 220-240 V / 50 Hz

Nominal input P1 1,1 kW

Output power P2 0,6 kW

Motorspeed 1/min. 2800

Work Place Emissions Values:

Empty Run Noise dB

(A) 96

Working Noise dB (A) 76

7. Assembly

For packaging reasons your machine is delivered in

semi-assembled state.

• Using the screws and nuts supplied, screw together

parts A, B and C of the cladding as shown in Figure

2+3.

• Mount the axle and rollers on the base plate with

the screws and nuts, see Figure 4+5. Then set the

chassis on the wheels.

• Screw the side parts D and E of the cladding toge-

ther in the middle using 3 screws and 3 nuts. (Fi-

gure 6+7)

• Fasten the screwed parts A, B, C to the side clad-

ding (D, E), see Figure 8+9.

• Set the fully assembled cladding on the base plate

of the chassis and fasten this using 4 screws and 4

nuts. (Figure 10)

• Position the housing with motor on the cladding and

screw it tight using the screws and nuts. (Figure

11+12)

• Slide the clamping strip through the loops on the

lter bag.

• Insert the retainer rod in the housing and hang the

lter bag over it, then fasten the lter bag to the con-

tainer using the clamping strip (Figure 13+14).

• Note the information published by your professio-

nal associations.

• Do not use any low-powered machines for heavy

duty work.

• Do not mis-use the cable

• Make sure you stand squarely and keep your ba-

lance at all times.

• Check that the moving parts are in good working

order, that they do not jam, and that no parts are

damaged. Make sure that all parts are tted cor-

rectly and that all other operating conditions are

properly fullled.

• Unless otherwise stated in the operating instruc-

tions, damaged safety devices and parts have to

be repaired or replaced by an authorized service

center.

• Have damaged switches replaced by a customer

service workshop.

• This electric tool complies with the pertinent safety

regulations. Repairs are to be carried out only by

a qualied electrician using original replacement

parts or the user may suffer an accident.

• If necessary, wear suitable personal protection

equipment. This could consist of:

- Ear-muffs to prevent the risk of damaging your

hearing

- A breathing mask to prevent the risk of inhaling

hazardous dust

• The operator has to be informed about the condi-

tions with an inuence on noise development.

• Faults on the machine have to be reported to the

person in charge as soon as they are discovered.

• This appliance is not suitable for the collection of

dangerous dust.

• This equipment is not designed to be used by peop-

le (including children) with limited physical, sensory

or mental capacities or those with no experience

and/or knowledge unless they are supervised by a

person who is responsible for their safety or they

have received instructions from such a person in

how to use the equipment safely. Children must al-

ways be supervised in order to ensure that they do

not play with the equipment.

Remaining hazards

The machine has been built using modem techno-

logy in accordance with recognized safety rules.

Some remaining hazards, however, may still exist.

• Wood chips and sawdust can be health hazards.

Be sure to wear personal protective gear such as

safety goggles and a dust mask.

• Dust inhalation may occur when closing and replac-

ing the dust bag.

• Please note the instructions concerning proper dis-

posal in the operating manual (e.g. the use of P2

dust masks) to prevent dust inhalation.

• Noise can be a health hazard. The permitted noise

level is exceeded when working. Be sure to wear

personal protective gear such as ear protection.

• The use of incorrect or damaged mains cables can

lead to injuries caused by electricity.

• Even when all safety measures are taken, some re-

maining hazards which are not yet evident may still

be present.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Scheppach HD15 Seite 19

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info