Bedienungsanleitung Scheppach HG34 (Seite 22 von 124) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Polnisch, Schwedisch, Norwegisch)

781661

Zoom out

Zoom in

Vorherige Seite

1/124

Nächste Seite

22 GB

 www.scheppach.com /  service@scheppach.com /  +(49)-08223-4002-99 /  +(49)-08223-4002-58

• Rough work: hold the drive unit like the handle of a

hammer.

8.5 Grinding

• Place the workpiece onto the workpiece support (8)

and slowly guide the workpiece towards the grind-

ing wheel (5) at the desired angle to the point where

workpiece and grinding wheel make contact.

• Move the workpiece slightly back and forth to pro-

duce an optimal grinding result. This way the grind-

ing wheel (5) will be evenly worn. Allow the work-

piece to cool down occasionally.

Important!

If the grinding wheel becomes jammed during op-

eration, remove the workpiece and wait until the tool

reaches its top speed again.

8.6 Polishing

• Apply a thin coating of polishing paste to the grind-

ing surface of the polishing wheel (6) (Fig. 18/ Item

3).

• Press on the workpiece in the polishing direction

and move back and forth from left to right in a pen-

dulum action.

• Always carry out polishing work in the direction of

rotation of the polishing wheel (6).

Important!

Polishing in the opposite direction to the direction

of rotation of the polishing wheels can cause damage

to the polishing wheels, which in turn can

result in injuries.

9. Cleaning, maintenance

Always pull out the mains power plug before starting

any cleaning work.

9.1 Cleaning

• Keep all safety devices, air vents and the motor

housing free of dirt and dust as far as possible.

Wipe the equipment with a clean cloth or blow it with

compressed air at low pressure.

• We recommend that you clean the device

immediately each time you have nished using it.

• Clean the equipment regularly with a moist cloth

and some soft soap. Do not use cleaning agents

or solvents; these could attack the plastic parts of

the equipment. Ensure that no water can seep into

the device. The ingress of water into an electric tool

increases the risk of an electric shock.

9.2 Maintenance

There are no parts inside the equipment which require

additional maintenance.

7.6 Installing the  exible shaft (Fig. 10)

• Insert the internal axle (a) of the exible shaft (12)

into the guide shaft of the equipment.

• Secure the fastening nut of the exible shaft to the

equipment thread by hand (left-hand thread).

Important!

When you work with the  exible shaft (12), the

safety glass (2) must be placed right up against

the workpiece support (8) in order to prevent uncon-

trolled touching of the wheels.

7.7 Inserting the various tools into the  exible

shaft (Fig. 11)

1. Press the supplied locking pin (13) into the hole in

the  exible shaft (12) and turn the shaft until the

pin latches in place.

2. Now undo the collet chuck nut.

3. Insert the required tool into the sleeve as far as the

stop and screw the collet chuck nut tight.

8. Operation

8.1 On/Off switch (1)

• To switch on the equipment set the On/Off switch

• (1) to position I.

• Move the On/Off switch (1) to position 0 to switch

• off the equipment.

Important!

When you are not working with the  exible shaft (12),

it is not allowed to be mounted on the equipment be-

cause it could then  y around out of control.

After switching on, wait for the equipment to reach its

maximum speed of rotation. Only then should you be-

gin with the grinding.

8.2. Speed selector (Fig. 1)

The required speed can be set with the speed control

(11).

8.2.1 Speed of the  exible shaft

The correct speed depends on the tool used and

the type of material being processed.

8.3. Information on speed settings

• Small cutters/grinding pins: High speed

• Large cutters/grinding pins: Low speed

8.4. Work practice

• Exert only moderate pressure on the workpiece so

that it can be machined at constant speed.

• Instead of accelerating your work, high pressure will

cause the drive unit to slow down and even stop,

thus overloading the motor.

• For your own safety, it is essential to secure small

workpieces with a screw clamp or vise.

• Precision work/engraving: hold the drive unit like a

pen.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Scheppach HG34 Seite 22

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info