Bedienungsanleitung Scheppach HL1300 (Seite 24 von 144) (Deutsch, Englisch, Französisch, Italienisch, Polnisch)

781954

Zoom out

Zoom in

Vorherige Seite

1/144

Nächste Seite

 www.scheppach.com /  service@scheppach.com /  +(49)-08223-4002-99 /  +(49)-08223-4002-58

24 | GB

If the splitting blade does not move despite activation

of the handles or return bracket, immediately turn o󰀨

the machine. Turn the pole reversing unit in the plug-

in module (g. 11) to change the rotational direction

of the motor.

Never let the motor run in the wrong direction!

This will inevitably destroy the pump system and

no warranty claim can be made.

Functional test

Test the function before every use.

Action: Result:

Push both handles

towards below.

Splitting knife goes down

to approx. 20 cm above

the table.

Let one handle loose,

then the other.

Splitting knife stops in the

desired position.

Push both handles

towards up

Splitting knife returns to

upper position

Warning!

Loosen the lling screw (d) before commission-

ing. Never forget to loosen the lling screw! Oth-

erwise, the air in the system will constantly be

compressed and decompressed with the result

that the seals of the hydraulic circuit will be de-

stroyed and the wood splitter can no longer be

used. In this case, the seller and the manufactur-

er will not be liable to warranty services.

Switching on and o󰀨 (10)

Press the green button for switching on.

Press the red button for switching o󰀨.

Note: Check the function of the ON/OFF unit before

every use by switching on and o󰀨 once.

Restarting safety in case of current interruption

(no-volt release).

In case of current failure, inadvertent pulling of the

plug, or a defective fuse, the machine is switched o󰀨

automatically. For switching on again, press anew

the green button of the switch unit.

Fix the splitter

Fix the splitter on the oor by fastening the two brack-

ets (f) to the support plate with two hexagon screws

(g) each. Then insert the tent peg (h) through the ex-

isting hole at an angle.

Splitting

• If the outside temperature is below 5°C, let the ma-

chine run idle for about 5 minutes so the hydraulic

system reaches its operating temperature. Place

the log under the splitting blade vertically. Caution:

The splitting blade is very sharp. Risk of injury!

9.5 Mount trunk lifter (g. 6)

Fasten the trunk lifter (5) with a hexagon screw (M10

x 55) and a self-locking nut between both of the

brackets, which are located on the right, lower end

of the splitter.

Next, align the holder arm (6) on the trunk lifter. A gap

of approx. 0.5 - 1 mm must be present between the

holder arm and trunk lifter.

Next, cut in the chain (4) on the splitting blade. (g. 7)

9.6 Putting the splitter into the work position

Connect the splitter to the mains power. Be aware of

the motor’s direction of rotation.

Lower both controller handles until the cylinder is

present above the drilled holes (d) is located in the

upper position. Insert both shafts into the drilled holes

and secure them with spring pins.

Then bring the splitting blade to the top position and

remove the support. You must store the support safe-

ly because it is needed every time the splitter is trans-

ported.

m IMPORTANT!

You must fully assemble the appliance before using it

for the rst time!

10. Initial operation

Make sure the machine is completely and expertly

assembled. Check before every use:

• the connection cables for any defective spots

(cracks, cuts etc.).

• the machine for any possible damage.

• the rm seat of all bolts.

• the hydraulic system for leakage.

• the oil level.

• the safety devices

Checking the oil level (g. 9)

The hydraulic unit is a closed system with oil tank,

oil pump and control valve. Check the oil level regu-

larly before every use. Too low an oil level can dam-

age the oil pump. The level of oil must be checked

when the riving knife is pulled back. If the oil level is

at the lower notch, then the oil level is at a minimum.

Should this be the case, oil must be immediately

added. The upper notch indicates the maximum oil

level. The machine must be on level ground. Screw

in the oil dipstick fully, to measure the oil level.

E- Motor

Check the running direction of the motor. If the split-

ting arm is not in the top position, bring the splitting

blade in the top position, using the return bracket or

handles. If the splitting arm is already in the top posi-

tion, activate the splitting mechanism by moving both

levers down. This will move the splitting arm down.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Scheppach HL1300 Seite 24

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info