Bedienungsanleitung Scheppach HL1450 (Seite 23 von 124) (Deutsch, Englisch, Französisch, Italienisch)

781855

Zoom out

Zoom in

Vorherige Seite

1/124

Nächste Seite

 www.scheppach.com /  service@scheppach.com /  +(49)-08223-4002-99 /  +(49)-08223-4002-58

GB | 23

• Then remove the split wood and move the riving

knife and therefore the log lifter back down.

• Now you can roll a new log onto the log lifter.

Resetting the log lifter

This is used as a second guard arm when not using

the trunk lifter. For this, the arm is moved up until it

locks in.

Transport position of the log lifter:

• Using your hand, move the log lifter up until it locks

in position.

Comply with these notices to ensure quick and

safe work.

11. Electrical connection

The electrical motor installed is connected and ready

for operation. The connection complies with the ap-

plicable VDE and DIN provisions.

The customer‘s mains connection as well as the ex-

tension cable used must also comply with these reg-

ulations.

Damaged electrical connection cable

The insulation on electrical connection cables is of-

ten damaged.

This may have the following causes:

• Passage points, where connection cables are

passed through windows or doors.

• Kinks where the connection cable has been im-

properly fastened or routed.

• Places where the connection cables have been cut

due to being driven over.

• Insulation damage due to being ripped out of the

wall outlet.

• Cracks due to the insulation ageing.

Such damaged electrical connection cables must not

be used and are life-threatening due to the insula-

tion damage.

Check the electrical connection cables for damage

regularly. Make sure that the connection cable does

not hang on the power network during the inspection.

Electrical connection cables must comply with the

applicable VDE and DIN provisions. Only use con-

nection cables with the marking „H07RN“.

The printing of the type designation on the connec-

tion cable is mandatory.

For single-phase AC motors, we recommend a fuse

rating of 16A (C) or 16A (K) for machines with a high

starting current (starting from 3000 watts)!

Caution: The splitting blade is very sharp. Risk

of injury!

• When you push both operating levers down, the

splitting blade goes down and splits the wood.

• Only ever split logs that have been sawn off straight.

• Split the log vertically.

• Never split it lying down or diagonally to the grain!

• Wear suitable gloves and safety boots when split-

ting wood.

• Split very misshapen logs from the edge.

Caution: During splitting, some logs can be un-

der signicant tension and suddenly break.

• Force jammed logs out by applying pressure in

the splitting direction or by raising the riving

knife. In this case, only push the handles up,

do not use the return bracket. Caution: Risk of

injury

Using the retaining claw (Fig. 12)

During the splitting process, the wood (B) must

not be held in position with hands or feet. Use the

retaining claw for this (15). To do this, proceed as

follows:

1. Move the splitting wedge (9) a short way over the

wood to be split (B / max. 1 cm) using both oper-

ating handles (2).

2. Place the retaining claw (15) on the splitting

wedge (9).

3. Push the retaining claw (15) into the wood to be

split (B) using the tensioning lever. The attach-

ment points for the tensioning lever (16) is the

bolts (A).

4. Continue the splitting process using both operat-

ing levers (2).

5. Remove the retaining claw from the wood (B) be-

fore pressing the return lever (3).

Operating the log lifter (5)

General information about the log lifter:

• For safety reasons, the log lifter chain may only be

hung on the splitting blade with the last link.

• Ensure that nobody else is within the working envi-

ronment of the log lifter.

Operating the log lifter:

• Loosen the log lifter restraining the lifting tube can

move freely.

• Move the splitting blade so far down that the log

lifter lifting tube lies on the ground.

• In this position, you can roll the log to be split onto

the lifting tube. (The log has to be between the two

xing tips.)

• Push the return bracket down or the handles up

so the splitting blade moves up. (Caution! Do not

stand in the working environment of the log lifter!

Risk of injury!)

• Now align the log, push it against the retention

thorn and split it (see: Operating instructions).

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Scheppach HL1450 Seite 23

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info