Bedienungsanleitung Scheppach HL1600 (Seite 24 von 112) (Deutsch, Englisch, Französisch, Italienisch)

781856

Zoom out

Zoom in

Vorherige Seite

1/112

Nächste Seite

 www.scheppach.com /  service@scheppach.com /  +(49)-08223-4002-99 /  +(49)-08223-4002-58

24 | GB

Functional test

Test the function before every use.

Action: Result:

Push both handles

towards below.

Splitting knife goes down

to approx. 20 cm above the

table.

Let one handle

loose, then the

other.

Splitting knife stops in the

desired position.

Let both handles

loose.

Splitting knife returns to

upper position.

Warning!

Loosen the lling screw (Fig. 17) before commis-

sioning.

Never forget to loosen the lling screw! Other-

wise, the air in the system will constantly be com-

pressed and decompressed with the result that

the seals of the hydraulic circuit will be destroyed

and the wood splitter can no longer be used. In

this case, the seller and the manufacturer will not

be liable to warranty services.

Switching on and off (11)

Press the green button for switching on.

Press the red button for switching off.

Note: Check the function of the ON/OFF unit before

every use by switching on and off once.

Restarting safety in case of current interruption

(no-volt release).

In case of current failure, inadvertent pulling of the

plug, or a defective fuse, the machine is switched off

automatically. For switching on again, press anew the

green button of the switch unit.

Using the safety arm (Fig. 14)

The safety arm can be set at different height posi-

tions, depending on the length of the wood.

Splitting (Fig. 15)

• If the outside temperature is below 5°C, let the ma-

chine run idle for about 5 minutes so the hydraulic

system reaches its operating temperature. Place

the log under the splitting blade vertically.

Caution: The splitting blade is very sharp. Risk

of injury!

• When you push both operating levers down, the

splitting blade goes down and splits the wood.

• Only ever split logs that have been sawn off straight.

• Split the log vertically.

• Never split it lying down or diagonally to the grain!

• Wear suitable gloves and safety boots when split-

ting wood.

• Split very misshapen logs from the edge.

Caution: During splitting, some logs can be un-

der signicant tension and suddenly break.

9.8 Moving the transport handle (2) to the trans-

port position (g. 13)

The transport handle is already pre-assembled on

the splitter and is xed in working position. Release

the tension lever (1) and move the transport handle

(2) down until you can insert the tension lever into the

next hole and x the transport handle in the position

(3).

m IMPORTANT!

You must fully assemble the appliance before using it

for the rst time!

10. Initial operation

Make sure the machine is completely and expertly as-

sembled. Check before every use:

• The connection cables for any defective spots

(cracks, cuts etc.).

• The machine for any possible damage.

• The rm seat of all bolts.

• The hydraulic system for leakage.

• The oil level.

Checking the oil level

The hydraulic unit is a closed system with oil tank, oil

pump and control valve. Check the oil level regularly

before every use. Too low an oil level can damage

the oil pump. The level of oil must be checked when

the riving knife is pulled back. If the oil level is at the

lower notch, then the oil level is at a minimum. Should

this be the case, oil must be immediately added. The

upper notch indicates the maximum oil level. The ma-

chine must be on level ground. Screw in the oil dip-

stick fully, to measure the oil level.

E- Motor

Check the running direction of the motor. If the split-

ting arm is not in the top position, bring the splitting

blade in the top position, using the return bracket or

handles. If the splitting arm is already in the top posi-

tion, activate the splitting mechanism by moving both

levers down. This will move the splitting arm down. If

the splitting blade does not move despite activation of

the handles or return bracket, immediately turn off the

machine. Turn the pole reversing unit in the plug-in

module (Fig. 11 + 12) to change the rotational direc-

tion of the motor.

Never let the motor run in the wrong direction!

This will inevitably destroy the pump system and

no warranty claim can be made.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Scheppach HL1600 Seite 24

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info