Bedienungsanleitung Scheppach HL3000GM (Seite 28 von 120) (Deutsch, Englisch, Französisch, Italienisch)

781854

Zoom out

Zoom in

Vorherige Seite

1/120

Nächste Seite

 www.scheppach.com /  service@scheppach.com /  +(49)-08223-4002-99 /  +(49)-08223-4002-58

28 | GB

The system is complete when the machine is deliv-

ered, and may not be changed or manipulated.

Connections and repairs

Connections and repairs of electrical equipment may

only be carried out by an electrician.

ATTENTION ! Observe the correct direction of rota-

tion when inserting the saw blade.

Please provide the following information in the event

of any enquiries:

• Type of current for the motor

• Machine data - type plate

Service information

Please note that the following parts of this product

are subject to normal or natural wear and that the fol-

lowing parts are therefore also required for use as

consumables.

Wear parts*: splitting wedge guides, hydraulic oil,

splitting wedge, Transmission oil

* Not necessarily included in the scope of delivery!

16. Disposal and recycling

The equipment is supplied in packaging to prevent it

from being damaged in transit. The raw materials in

this packaging can be reused or recycled. The equip-

ment and its accessories are made of various types

of material, such as metal and plastic.

Defective components must be disposed of as spe-

cial waste. Ask your dealer or your local council.

Old devices must not be disposed of with house-

hold waste!

This symbol indicates that this product must

not be disposed of together with domestic

waste in compliance with the Directive

(2012/19/EU) pertaining to waste electrical and elec-

tronic equipment (WEEE). This product must be dis-

posed of at a designated collection point. This can

occur, for example, by handing it in at an authorised

collecting point for the recycling of waste electrical

and electronic equipment. Improper handling of

waste equipment may have negative consequences

for the environment and human health due to poten-

tially hazardous substances that are often contained

in electrical and electronic equipment. By properly

disposing of this product, you are also contributing

to the effective use of natural resources. You can

obtain information on collection points for waste

equipment from your municipal administration, pub-

lic waste disposal authority, an authorised body for

the disposal of waste electrical and electronic equip-

ment or your waste disposal company.

15. Maintenance

Attention!

Pull out the power plug before carrying out any main-

tenance work on the equipment. Make sure that the

drive shaft is not connected to the traction unit.

When must the oil be changed?

First oil change after 50 operating hours, then every

250 operating hours.

Oil change (Fig. 18)

Position the kindling splitter on a slightly raised sur-

face (e.g. euro pallet). Place a sufciently large con-

tainer (at least 30 litres) under the drain plug on the

splitting column. Open the drain plug and carefully let

the oil run into the container.

Open the lling screw on the top of the split-

ting column so the oil can drain more easily. Re-

place the drain plug and its seal and tighten it.

Pour in fresh hydraulic oil (Contents: see Technical

data) and check the oil level with the dipstick. After

changing the oil, operate the kindling splitter a few

times without actually splitting.

Warning! Ensure that no debris gets into the oil

container.

Dispose of the used oil in a correct manner at a

public collection facility. It is prohibited to drop

old oil on the ground or to mix it with waste.

We recommend oil from the HLP 32 range.

Changing the transmission oil, Fig. 20

The transmission has been lled with SAE90 trans-

mission oil by the factory. After the rst 50 operating

hours, drain the transmission oil and replace it as de-

scribed with new oil. The next oil changes will then

need to be carried out every 250 operating hours or

every six months, depending on which happens rst.

1. Disassemble the drive shaft protective cap and

place a sufciently large container under the

transmission.

2. First open the oil drain plug (19), then the oil ller

opening (17) and completely drain the oil.

3. Close the oil drain plug with a new seal and, using

a funnel, pour in new SAE90 transmission oil into

the ller opening until the lower edge of the sight

glass (18) is almost covered in oil.

Check the oil level every 8 hours. The oil level is cor-

rect when the lower edge of the display (18) is almost

covered in oil.

Hydraulic system

The hydraulic unit is a closed system with oil tank, oil

pump and control valve.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Scheppach HL3000GM Seite 28

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info