Bedienungsanleitung Scheppach HL730 (Seite 22 von 136) (Deutsch, Englisch, Französisch, Italienisch, Polnisch, Schwedisch, Norwegisch)

781852

Zoom out

Zoom in

Vorherige Seite

1/136

Nächste Seite

 www.scheppach.com /  service@scheppach.com /  +(49)-08223-4002-99 /  +(49)-08223-4002-58

22 | GB

Venting (g. 14)

Before working with the log splitter, vent the hydraulic

system.

• Release the venting cap 14 by a few revolutions so

the air can escape from the oil tank.

• Leave the cap open during the operation.

• Before you move the log splitter, close the cap

again in order not to lose any oil.

If the hydraulic system is not vented, the enclosed air

will damage the gaskets and with it the complete log

splitter.

Stroke limit for short logs (g. 14)

Lower splitting knife position about 10 cm above ta-

ble.

• Move splitting knife to the desired position

• Release one operating arm

• 󰀨

• Release the second operating arm

• Undo the star grip screw (10a)

• Push the stroke set rod (8) to the top until it is

stopped by the spring

• Tighten the star grip screw (10a) again.

• Switch motor on

• Check upper position

Switching on and o󰀨 (12)

Press the green button for switching on.

󰀨

Note: Check the function of the ON/OFF unit before

󰀨

Restarting safety in case of current interruption

(no-volt release).

In case of current failure, inadvertent pulling of the

󰀨

automatically.

For switching on again, press anew the green button

of the switch unit.

Splitting

• Place the log on the table, hold it with both handles,

press the handles down. As soon as the splitting

knife enters the wood, push the handles down and

to the outside at the same time. This prevents the

wood from putting pressure on the holder plates.

• Only split straight cut logs.

• Split the logs in vertical position.

• Never split in horizontal position or across.

• Wear protective gloves when splitting.

End of work

• Move the splitting knife to the lower position.

• Release one operating arm.

• 󰀨

• Close the venting cap.

• Observe the general maintenance instructions.

9.4 Fitting the claws (enclosed accessories

bag C)

• Fasten the additional retainers (D) to the claws with



• Make sure that the larger additional retainer is

fastened with the left claw (4).

• Place the adjustable claws on the hexagon nuts

previously attached, and fasten these with the star



• Note that the prongs on the claws must point



m IMPORTANT!

You must fully assemble the appliance before using it



10. Initial operation

Make sure the machine is completely and expertly

assembled. Check before every use:

• The connection cables for any defective spots

(cracks, cuts etc.).

• The machine for any possible damage.

• 

• The hydraulic system for leakage.

• The oil level.

Checking the oil level (g. 13)

The hydraulic unit is a closed system with oil tank, oil

pump and control valve. Check the oil level regularly

before every use. Too low an oil level can damage

the oil pump. The correct oil level is approx. 10 to 20

mm below the oil tank surface.

Note: The level of oil must be checked when the riv-

ing knife is pulled back. If the oil level is at the low-

er notch, then the oil level is at a minimum. Should

this be the case, oil must be immediately added. The

upper notch indicates the maximum oil level. The

machine must be on level ground. Screw in the oil

dipstick fully, to measure the oil level.

Functional test

Test the function before every use.

Action: Result:

Push both handles towards

below.

Splitting knife goes

down to approx. 10

cm above the table.

Let one handle loose, then

the other.

Splitting knife stops

in the desired po-

sition.

Let both handles loose. Splitting knife

returns to upper

position.

Check the oil level before every use – see chap-

ter “Maintenance“.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Scheppach HL730 Seite 22

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info