Bedienungsanleitung Scheppach HM80L (Seite 27 von 228) (Alle Sprachen)

781434

Zoom out

Zoom in

Vorherige Seite

1/228

Nächste Seite

 www.scheppach.com /  service@scheppach.com /  +(49)-08223-4002-99 /  +(49)-08223-4002-58

GB | 27

Then the handle must be re-tightened.

12. Working instructions

After you have carried out all the tasks described

above, you can begin working.

ATTENTION: Always keep your hands away from

the cutting zone and never attempt to reach in while

cutting.

FIXING A WORKPIECE

Clamp the work piece on the work table with the

workpiece clamp (10 - Fig 1) in order to x it in place.

Cross cut 90° and turntable 0° (Fig. 4, 1.3)

Attention! For 90° mitre cuts, the moveable stop rail

(27a) must be xed in the inner position.

• Open the set screw (27b) on the moveable stop

rail (27a) with an Allen key and push the moveable

stop rail (27a) inwards.

• The moveable stop rail (27a) must be locked in a

position far enough from the inner position that the

distance between the stop rail (27a) and the saw

blade (5) is no more than 8 mm.

• Before making the cut, check that no collision

could occur between the stop rail (27a) and the

saw blade (5).

• Secure the locking lever (27b) again.

• Loosen the locking knob (26).

• Lift the saw unit by the handle (2) until it locks in

place in the top position.

• Lock the material with the clamping device (10)

on the xed saw table to prevent the material from

moving during the cutting operation.

• Press the workpiece evenly on the stop strips (27);

make sure that you hand remains outside the cut-

ting area of the saw blade.

• With your right hand on the handle (2), press the

locking lever (3) so that the unit can also be piv-

oted downward.

• The motor starts when the start button (1) is

pressed.

• Slowly bring the saw blade down to the workpiece

and cut through it with moderate pressure.

• When the cutting operation is completed, move the

machine head back to its upper (home) position

and release the ON/OFF button (1).

Attention! The machine executes an upward

stroke automatically due to the return spring, i.e.

do not release the handle (2) after completing the

cut; instead allow the machine head to move up-

wards slowly whilst applying light counter pressure.

Cross cut 90° and turntable 0° - 45° (Fig. 4, 2, 1.3)

The crosscut saw can be used to make crosscuts of

0°-45° to the left and 0° -45° to the right in relation

to the stop rail.

• Make sure that the work piece support (15) is

also guided through the two plates (19) on the

underneath.

• Afterwards, retighten the cross-head screw (14).

• Repeat this process on the other side.

Assembling the support stand (g. 1.1 – 1.2)

• Loosen the cross-head screws (18) on the

underneath of the saw and guide the support stand

(16) through the specied holes on the back of the

saw.

• Afterwards, retighten the cross-head screws (18).

10. Area of application

Intended application possibilities

The machine cuts:

• Wood and materials similar to wood

• Plastic

Unintended application possibilities

The machine is not suitable for:

• Ferritic materials, steel and cast iron, as well as

other material types which are not listed, particu-

larly food.

• Mitre saw without guard.

• Materials larger than the specied cutting data:

90°/90°/120 x 60 mm

90°/45° 80 x 60 mm

45°/90° 120 x 35 mm

45°/45° 80 x 35 mm

11. Settings

CROSS-CUTTING

ATTENTION: Before carrying out the following ad-

justments, please check whether the motor of the

machine is switched off.

Pivoting the table plate (Fig. 2)

The mitre saw can be pivoted left and right with the

rotary table. Exact angle adjustment is possible on

the basis of the scale. The angle can be precisely

and quickly adjusted from 0° to 45° with locking posi-

tions at 15°, 22.5° and 30°.

To pivot the rotary table, loosen the set screw (21)

and rotate the unit using the handle (20) until the de-

sired angle is reached. Then secure it with the set

screw (21).

Tilt of the saw unit (Fig. 3)

The saw unit can be tilted at an angle of up to 45°.

Loosen the handle (23) on the rear side of the ma-

chine and tilt the unit to the desired angle position

according to the scale. The angle can be set on

the basis of the scale (24) using the pointer (25).

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Scheppach HM80L Seite 27

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info