Bedienungsanleitung Scheppach HM90LXU (Seite 24 von 80) (Deutsch, Englisch, Französisch, Italienisch, Portugiesisch, Spanisch)

782505

Zoom out

Zoom in

Vorherige Seite

1/80

Nächste Seite

24 GB

• Do not load the machine unnecessarily: excessi-

ve pressure when sawing will quickly damage the

saw blade, which results in reduced output of the

machine in the processing and in cut precision.

• When cutting plastic material, please always use

clamps: the parts which should be cut must always

be xed between the clamps.

• Avoid accidental starting of the machine: the ope-

rating button may not be pressed when inserting

the plug in an outlet.

• Use the tool that is recommended in this manual.

In doing so, your mitre saw provides optimal per-

formance.

• Hands may never enter the processing zone when

the machine is in operation. Release the hand-

le button and switch off the machine prior to any

operations.

7. Technical data

AC motor 220 - 240 V ~ 50Hz

Power 1500 Watt

Operating mode S1*

Idle speed n04500 min-1

Carbide saw blade ø 216 x ø 30 x 2,8

Number of teeth 24

Swivel range -47° / 0°/ +47°

Mitre cut 0° bis 45° nach links

Saw width at 90° 305 x 70 mm

Saw width at 45° 215 x 70 mm

Saw width at 2 x 45°

(double mitre cut) 215 x 35 mm

Protection class II

Weight approx. 10.5 kg

Laser class 2

Wavelength of laser 650 nm

Laser output ≤ 1 mW

The work piece must have a minimum height of 3mm

and a minimum width of 10 mm.

Make sure that the workpiece is always secured with

the clamping device.

Noise

Total vibration values determined in accordance with

EN 61029.

sound pressure level LpA 93.6 dB(A)

uncertainty KpA 3 dB

sound power level LWA 106.6 dB(A)

uncertainty KWA 3 dB

Wear hearing protection.

The effects of noise can cause a loss of hearing.

8. Before starting the equipment

• The equipment must be set up where it can stand

securely, i.e. it should be bolted to a workbench, a

universal base frame or similar.

• All covers and safety devices have to be properly

tted before the equipment is switched on.

• It must be possible for the blade to run freely.

• When working with wood that has been processed

before, watch out for foreign bodies such as nails

or screws, etc.

• Before you press the ON/OFF switch check that

the saw blade is tted correctly. Moving parts must

run smoothly.

• Before you connect the equipment to the power

supply make sure the data on the rating plate are

dentical to the mains data.

9. Attachment and operation

9.1 Attaching the saw (Fig1/2/3/4/5)

• In order to adjust the rotary table (15) loosen the

set screw (11) approx. 2 turns.

• Turn the rotary table (15) and pointer (13) to the

desired angle measurement on the scale (14) and

secure with the set screw (11).

• Pressing the machine head (4) lightly downwards

and removing the locking bolt (24) from the motor

bracket at the same time disengages the saw from

the lowest position.

• Swing the machine head (4) up until the release

lever (2) latches into place.

• It is possible to secure the clamping device (7) to

the left or right on the stationary saw bench (16).

Insert the clamping device (7) into the provided ho-

le on the rear side of the stop rail (17) and secure

it with the wing screw.

• Attach the workpiece supports (8) to the xed saw

table as shown in Figure 4 and fasten with the

screw (9).

• It is possible to tilt the machine head (4) a max. 45°

to the left by loosening the set screw (23).

9.2 Precision adjustment of the stop for crosscut

90° (Fig. 1/5/6)

• No stop angle included.

• Lower the machine head (4) and secure using the

locking bolt (24).

• Loosen the set screw (23).

• Position the angle stop (a) between the saw blade

(6) and the rotary table (15).

• Loosen the locknut (c). Adjust the adjusting screw

(27) until the angle between the saw blade (6) and

the rotary table (15) is 90 °.

• Retighten the locknut (c) to secure this setting.

• Finally, check the position of the angle display. If

necessary, loosen the pointer (20) with a cross-

slot screwdriver, set to the 0 ° position of the angle

scale (19) and tighten the retaining screw again.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Scheppach HM90LXU Seite 24

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info