Bedienungsanleitung Scheppach HM90LXU (Seite 26 von 80) (Deutsch, Englisch, Französisch, Italienisch, Portugiesisch, Spanisch)

782505

Zoom out

Zoom in

Vorherige Seite

1/80

Nächste Seite

26 GB

9.9 Sawdust bag (Fig. 1)

The saw is equipped with a debris bag (18) for saw-

dust and chips.

Squeeze together the metal ring on the dust bag and

attach it to the outlet opening in the motor area.

The debris bag (18) can be emptied by means of a

zipper at the bottom.

9.10 Changing the saw blade (Fig. 14-17)

Remove the power plug!

Important.

Wear safety gloves when changing the saw blade.

Risk of injury!

• Swing up the machine head (4).

• Undo the screw (g) on the guide bar (35), so that it

can move freely and be pivoted downwards.

• Loosen the screw (f) of the ange cover so that it

is free to move.

• Press the release lever (2). Swing up the saw bla-

de guard (5) to the point where the recess in the

saw blade guard (5) is above the ange bolt (29).

• Insert the allen key (e) in the ange bolt (29).

• Firmly press the saw shaft lock (31) and slowly

rotate the ange bolt (29) in clockwise direction.

The saw shaft lock (31) engages after no more

than one rotation.

• Now, using a little more force, slacken the ange

bolt (29) in the clockwise direction.

• Turn the ange screw (29) right out and remove

the external ange (30).

• Take the blade (6) off the inner ange (32) and pull

out downwards.

• Carefully clean the ange screw (29), outer ange

(30) and inner ange (32).

• Fit and fasten the new saw blade (6) in reverse

order.

• Important! The cutting angle of the teeth, in other

words the direction of rotation of the saw blade (6)

must coincide with the direction of the arrow on

the housing.

• Move the guide bar (35) into position and tighten

the screw (f; g) again.

• Before continuing your work make sure that all sa-

fety devices are in good working condition.

• Important! Every time that you change the saw

blade (6), check to see that it spins freely in the

table insert (10) in both perpendicular and 45° ang-

le settings.

• Important! The work to change and align the saw

blade (6) must be carried out correctly.

9.11 Using the laser (Fig. 18)

• To switch on: Move the ON/OFF switch of the laser

(34) to the “1” position. A laser line is projected on-

to the material you wish to process, providing an

exact guide for the cut.

• To switch off: Move the ON/OFF switch of the laser

(34) to the “0” position.

9.12 Adjusting the laser (Fig. 19)

If the laser (33) ceases to indicate the correct cutting

line, you can readjust the laser. To do so, open the

screws (36) and set the laser by moving sideways to

that the laser beam strikes the teeth of the saw blade

(6).

10. Transport

• Tighten the set screw (11) in order to lock the ro-

tary table (15)

• Activate the release lever (2), press the machine

head (4) downwards and secure with the safety pin

(24). The saw is now locked in its bottom position.

• Fix the saw’s drag function with the locking screw

for drag guide (21) in rear position.

• Carry the equipment by the xed saw table (16).

• When reassembling the equipment proceed as de-

scribed under section 8.

11. Maintenance

m Warning! Prior to any adjustment, mainte-

nance or service work disconnect the mains po-

wer plug!

General maintenance measures

Wipe chips and dust off the machine from time to

time using a cloth. In order to extend the service life

of the tool, oil the rotary parts once monthly. Do not

oil the motor.

When cleaning the plastic do not use corrosive pro-

ducts.

Brush inspection

Check the carbon brushes after the rst 50 opera-

ting hours with a new machine, or when new brushes

have been tted. After carrying out the rst check,

repeat the check every 10 operating hours.

If the carbon is worn to a length of 6 mm, or if the

spring or contact wire are burned or damaged, it is

necessary to replace both brushes. If the brushes

are found to be usable following removal, it is possib-

le to reinstall them.

Service information

Please note that the following parts of this product

are subject to normal or natural wear and that the fol-

lowing parts are therefore also required for use as

consumables.

Wear parts*: Carbon brush, saw blade, table inserts,

dust bags,

* Not necessarily included in the scope of delivery!

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Scheppach HM90LXU Seite 26

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info