Bedienungsanleitung Scheppach HM90MP (Seite 26 von 168) (Deutsch, Englisch, Französisch, Italienisch, Polnisch, Alle Sprachen)

781435

Zoom out

Zoom in

Vorherige Seite

1/168

Nächste Seite

 www.scheppach.com /  service@scheppach.com /  +(49)-08223-4002-99 /  +(49)-08223-4002-58

26 | GB

f) Do not reach behind the fence with either

hand closer than 100 mm from either side of

the saw blade, to remove wood scraps, or for

any other reason while the blade is spinning.

The proximity of the spinning saw blade to your

hand may not be obvious and you may be seri-

ously injured.

g) Inspect your workpiece before cutting. If the

workpiece is bowed or warped, clamp it with

the outside bowed face toward the fence. Al-

ways make certain that there is no gap be-

tween the workpiece, fence and table along

the line of the cut. Bent or warped workpieces

can twist or shift and may cause binding on the

spinning saw blade while cutting. There should

be no nails or foreign objects in the workpiece.

h) Do not use the saw until the table is clear

of all tools, wood scraps, etc., except for

the workpiece. Small debris or loose pieces of

wood or other objects that contact the revolving

blade can be thrown with high speed.

i) Cut only one workpiece at a time. Stacked

multiple workpieces cannot be adequately

clamped or braced and may bind on the blade or

shift during cutting.

j) Ensure the mitre saw is mounted or placed

on a level, rm work surface before use. A

level and rm work surface reduces the risk of

the mitre saw becoming unstable.

k) Plan your work. Every time you change the

bevel or mitre angle setting, make sure the

adjustable fence is set correctly to support

the workpiece and will not interfere with the

blade or the guarding system. Without turn-

ing the tool “ON” and with no workpiece on the

table, move the saw blade through a complete

simulated cut to assure there will be no interfer-

ence or danger of cutting the fence.

l) Provide adequate support such as table ex-

tensions, saw horses, etc. for a workpiece

that is wider or longer than the table top.

Workpieces longer or wider than the mitre saw

table can tip if not securely supported. If the cut-

o󰀨 piece or workpiece tips, it can lift the lower

guard or be thrown by the spinning blade.

m) Do not use another person as a substitute

for a table extension or as additional sup-

port. Unstable support for the workpiece can

cause the blade to bind or the workpiece to shift

during the cutting operation pulling you and the

helper into the spinning blade.

n) The cut-o󰀨 piece must not be jammed or

pressed by any means against the spinning

saw blade. If conned, i.e. using length stops,

the cut-o󰀨 piece could get wedged against the

blade and thrown violently.

5) Service

a) Have your power tool serviced by a qualied

repair person using only identical replace-

ment parts.

This will ensure that the safety of the power tool

is maintained.

Warning!

This electric tool generates an electromagnetic eld

during operation. This eld can impair active or pas-

sive medical implants under certain conditions. In or-

der to prevent the risk of serious or deadly injuries,

we recommend that persons with medical implants

consult with their physician and the manufacturer of

the medical implant prior to operating the electric tool.

Safety instructions for mitre saws

a) Mitre saws are intended to cut wood or

wood-like products, they cannot be used

with abrasive cut-o󰀨 wheels for cutting fer-

rous material such as bars, rods, studs, etc.

Abrasive dust causes moving parts such as the

lower guard to jam. Sparks from abrasive cutting

will burn the lower guard, the kerf insert and oth-

er plastic parts.

b) Use clamps to support the workpiece when-

ever possible. If supporting the workpiece

by hand, you must always keep your hand

at least 100 mm from either side of the saw

blade. Do not use this saw to cut pieces that

are too small to be securely clamped or held

by hand. If your hand is placed too close to the

saw blade, there is an increased risk of injury

from blade contact.

c) The workpiece must be stationary and

clamped or held against both the fence and

the table. Do not feed the workpiece into the

blade or cut “freehand” in any way. Unre-

strained or moving workpieces could be thrown

at high speeds, causing injury.

d) Push the saw through the workpiece. Do

not pull the saw through the workpiece. To

make a cut, raise the saw head and pull it out

over the workpiece without cutting, start the

motor, press the saw head down and push

the saw through the workpiece. Cutting on

the pull stroke is likely to cause the saw blade to

climb on top of the workpiece and violently throw

the blade assembly towards the operator.

e) Never cross your hand over the intended line

of cutting either in front or behind the saw

blade. Supporting the workpiece “cross hand-

ed” i.e. holding the workpiece to the right of the

saw blade with your left hand or vice versa is

very dangerous.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Scheppach HM90MP Seite 26

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info