Bedienungsanleitung Scheppach HMS850 (Seite 22 von 148) (Deutsch, Englisch, Dänisch, Französisch, Italienisch, Polnisch)

759249

Zoom out

Zoom in

Vorherige Seite

1/148

Nächste Seite

22 GB

• Machines tted with a sawdust extractor and

extractor hoods must be connected to the devices

concerned. The type of material used can have a

negative inuence on the dust generated.

• The machine is designed exclusively for the cut-

ting of wood and similar materials.

• The knife must be replaced immediately once it

becomes worn down by 5%.

• If a push stick is not used there may be a risk of

serious danger. The push stick should always be

kept at the machine when not used.

• There is a greater risk of danger when small

workpieces are fed in by hand. Always observe

the manufacturer’s instructions on the use of the

push stick.

• If the safety covers, infeed table or mesh are in-

correctly aligned they could lead to uncontrollable

situations.

• Damaged or soiled workpieces may cause a risk

of danger. Never use metal parts in the machine or

any materials which can fracture or shatter. Risk

of injury!

• To cut long workpieces, always place them on a

mobile table or similar type of supporting equip-

ment. Otherwise there is a risk that you may lose

control over the workpiece.

• The machine is only suitable for planing and thick-

nessing.

• Wear suitable protective clothing when working

with the machine:

- ear protection to prevent damage to your ears,

- a breathing mask to avoid the risk of inhaling

hazardous particles of dust,

- safety gloves to avoid injuries from sharp edges

or knives,

- safety goggles to avoid eye injuries from ying

parts.

• It is imperative that the following situations are

avoided at all times: Premature interruption of the

cutting operation (planing cuts which do not com-

plete the entire length of the workpiece; planing of

uneven pieces of wood which do not lie at on the

infeed table).

• Important! If the primary mains connection is in a

poor condition there is a risk of short-circuits when

the machine is switched on. This may also affect

other functions (e.g. the lighting up of indicator

lamps). Should there be any faults in the primary

mains connection, please contact your local elec-

tricity supplier to advice and information.

Residual risks

Even when the machine is used as prescribed it is

still impossible to eliminate certain residual risk fac-

tors. There is a risk of the following injuries in con-

nection with the required operation of the machine:

• m WARNING! Danger of injury!

of ngers and hands by contact with the blade

shaft at uncovered areas when changing tools.

These can also be crushed by opening the guard.

• Eye injuries

• on the infeed and discharge opening by

dangerous recoil

• Danger from current if the electric cables have not

been connected correctly.

• harmful wood duct may be generated if operated

without an extractor or chip bag.

• by catapulted parts

• Metal parts in the workpiece can blunt or destroy

the blades.

• Lung damage if no suitable protective dust mask

is used.

m WARNING! Hearing damage!

A longer stay in the immediate vicinity of the running

unit may cause hearing damage.

Wear ear protectors!

Despite the observance of the operating instructions

there still may be some hidden residual risks.

Emergency procedure

Conduct a rst-aid procedure adequate to the

injury and summon qualied medical attendance as

quickly as possible. Protect the injured person from

further harm and calm them down. For the sake of

eventual accident, in accordance with DIN 13164, a

workplace has to be tted with a rst-aid kit. It is es-

sential to replace any used material in the rst-aid kit

immediately after it has been used. If you seek help,

state the following pieces of information:

1. Accident site

2. Accident type

3. Number of injured persons

4. Injury type(s)

6. Technical data

AC motor: 230-240V ~

50 Hz

Power P: 1500 W

Protection type: IP20

Max. workpiece width: 204 mm

Max. workpiece height at

thickness opening: 120 mm

Surfacing plane table: 370 x 212 mm

Thicknessing table: 270 x 204 mm

Thicknessing feeding speed: 6 m/min

Idle speed of cutter block: 9000 min-1

Max. planing cross-cutting depth: 2 mm

Max. thicknessing cross-cutting depth: 2 mm

Max. angle of the parallel stop: 45°

Sawdust extractor: Ø 100 mm

Weight: 27 kg

Sound

Sound values were measured in accordance with

EN 61029.

Sound pressure level LpA 92,9 dB(A)

Uncertainty KpA 3 dB

Sound power level LWA 105,9 dB(A)

Uncertainty KWA 3 dB

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Scheppach HMS850 Seite 22

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info