Bedienungsanleitung Scheppach HMS850 (Seite 24 von 148) (Deutsch, Englisch, Dänisch, Französisch, Italienisch, Polnisch)

759249

Zoom out

Zoom in

Vorherige Seite

1/148

Nächste Seite

24 GB

9. Operation

m IMPORTANT!: The surfacing and thicknessing

plane has been specially designed for planing solid

wood. High alloy knives (21) are used for this pur-

pose. The contact surface of the workpiece must be

at for thicknessing. If you want to work on large or

heavy workpieces, the machine must be secured in

place (e.g. using the thread in the machine base).

• The ON/OFF switch (1) is on the left-hand side of

the machine. Press the green key “I” to switch on

the machine. Press the red key “0” to switch off

the machine.

• The machine is tted with an overload switch (35)

to protect the motor. In the event of an overload,

the machine will cut out automatically. After a

short time, the overload switch (35) can be reset

again.

• To work on long workpieces, use roller tables or

a similar supporting arrangement. Such optional

units are available from your local DIY stores.

They must be placed at the entry and exit ends of

the plane. Their height must be adjusted such that

the workpiece is horizontal when it is fed into and

out of the machine.

9.1 Surfacing

m IMPORTANT!: Pull out the power plug before

performing any maintenance, cleaning and adjusting

work.

9.1.1 Adjustment (Figure 1/3/5)

• Turn the adjustment knob for cutting depth (11) to

set the height of the feed table (13). The set cutting

depth can be read off the scale (18).

• Loosen the parallel stop (6) with the clamp lever

(7). Set the required angle. The set angle can be

read off the scale (38). Secure the parallel stop (6)

with the clamp lever (7) again after making the set-

ting.

9.1.2 Fitting the chip extractor (Figure 6-8/16)

• Fit the hand crank (4) to the post on the planing ta-

ble (14). Turn the hand crank (4) counter-clockwise

to move the thicknessing table (20) to its lowest

position.

• Place the chip extractor (5) on the thicknessing

table (20).

• Turn the crank handle (4) clockwise until the chip

extractor (5) is rmly secure and the recess (C) is

on the safety switch (D2).

• Attach the extraction system adapter Ø 100 mm

(27) to the connection for a sawdust extractor (5).

• Connect the plane to a chip extraction system (not

supplied).

9.1.3 Surfacing mode (Figure 9/10)

• Undo the locking knob (32) and move the planing

knife cover (12) as far as necessary to accom-

modate the width of the workpiece. Re-tighten the

locking knob (32).

• Connect the mains plug to the mains lead. Press

the green button “I” to start the plane (1).

• Place the workpiece you wish to plane on the

feed table (13). Hold the slide blocks (2) with both

hands and slide the workpiece forwards towards

the planing table (14) over the knives (21).

• When you have nished work, switch off the

machine. To do this, press the red button “0”. Then

disconnect the machine from the mains supply.

• Remove the chips and dust from the feed table

(13), planing table (14) and knife block (23) after

the machine has reached a complete standstill.

• Return the planing knife cover (12) to its original

position.

9.2 Thicknessing

m IMPORTANT!: Pull out the power plug before

performing any maintenance, cleaning and adjusting

work.

9.2.1 Adjustment (Figure 13)

Place the hand crank (4) on the post on the planing

table (14) and turn it to adjust the thicknessing table

(20) to the required height. The set angle can be

read off the scale (29).

9.2.2 Fitting the chip extractor

(Figure 8, 11-13, 16)

• Undo the locking knob (32) and pull the planing

knife cover (12) forwards as far as possible.

• Place the chip extractor (5) on the planing table

(14). Ensure that the stop pins and the securing

screw (34) are in the appropriate holes and are

engaged in the internal threads on the planing

table (14) and that the recess (B) is on the safety

switch (D1).

• Turn the securing screw (34) until the chip extrac-

tor (5) is secure.

• Attach the extraction system adapter Ø 100 mm

(27) to the connection for a sawdust extractor (5).

• Connect the plane to a chip extraction system (not

supplied).

9.2.3 Thicknessing mode (Figure 11/13/17)

• Connect the mains plug to the mains lead. Press

the green button “I” to start the plane.

• Place a workpiece on the thicknessing table (20).

Guide the workpiece towards the feed table (13).

• When you have nished work, switch off the

machine. To do this, press the red button “0”. Then

disconnect the machine from the mains supply.

• Remove the chips and dust from the thicknessing

table (20) and knife block (23) after the machine

has reached a complete standstill.

• Use the pull-out workpiece support for long work-

pieces.

9.3 Changing the knives (Figure 17/18)

• m IMPORTANT!: Always pull the mains plug

before changing the knives.

• Remove the parallel stop following the instruc-

tions in 8.2 in reverse.

• Pull the planing knife cover (12) forwards as far

as possible so that the entire knife block (23) is

exposed.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Scheppach HMS850 Seite 24

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info