Bedienungsanleitung Scheppach HP2200S (Seite 29 von 148) (Deutsch, Englisch, Französisch, Italienisch, Polnisch)

781866

Zoom out

Zoom in

Vorherige Seite

1/148

Nächste Seite

 www.scheppach.com /  service@scheppach.com /  +(49)-08223-4002-99 /  +(49)-08223-4002-58  www.scheppach.com /  service@scheppach.com /  +(49)-08223-4002-99 /  +(49)-08223-4002-58

GB | 29

m Do not store compactor with fuel in a non-ven-

tilated area where fuel fumes may reach ame,

sparks, pilot lights or any ignition sources.

Use only approved fuel containers.

Store the device and its accessories in a dark, dry

and frost-proof place that is inaccessible to children.

The optimum storage temperature is between 5 and

30˚C.

Store the tool in its original packaging.

Cover the ool in order to protect it from dust and mois-

ture.

Store the operating manual with the tool.

14. Maintenance

m ATTENTION!

Always shut the engine down and remove the spark

plug connector before carrying out any maintenance

work.

Maintaining your compactor will insure long life to the

machine and its components.

• Preventive Maintenance Turn off engine. Engine

must be cool.

• Keep the engine’s throttle lever (1) in its SLOW po-

sition, and remove spark plug wire from spark plug

(8) and secure.

• Inspect the general condition of the plate compac-

tor. Check for loose screws, misalignment or bind-

ing of moving parts, cracked or broken parts, and

any other condition that may affect its safe opera-

tion.

• Then use a premium quality lightweight machine oil

to lubricate all moving parts.

• Clean the bottom of the compactor base as soon as

it begins to pick up soil being compacted. The unit

can not do a good job if the bottom surface is not

smooth and clean.

• Replace spark plug wire.

Checking and replacing V-belt

• To ensure optimum power transmission from the

engine to the eccentric shaft, the V-belt (k) must be

in good condition.

• If the V-belt (k) is torn, worn out or smooth, it must

be replaced.

Replacing V-belt (g. L)

• Turn off engine.

• Engine must be cool.

• Remove the belt guard (19) to access the V-belt (k).

• Loosen the four screws on the engine and push the

motor a little bit forwards.

• Pull the old V-belt (k) off the pulleys and pull a new

belt into place correctly.

m ATTENTION!

Never use a “pressure washer” to clean your plate

compactor. Water can penetrate tight areas of the unit

and cause damage to spindles, pulleys, bearings, or

the engine. The use of pressure washers will result in

shortened life and reduce serviceability.

12. Transport

See technical data for the weight of the machine. To

avoid burns or re hazards, let engine cool before lift-

ing/transporting machine or storing indoors.

When changing the machine position, it can be

equipped with the enclosed wheel kit (f) (see assem-

bling the wheel kit).

Loading the machine:

Lift unit by lift hook (3) on roll cage. Use a reliable

chain, cable or strap of adequate lifting capacity. The

unit must be transported in the upright position to pre-

vent fuel from spilling. Do not lay machine on its side

or top.

Secure or tie down unit using lift hook (3) or roll cage

when transporting.

m Machine may fall and cause damage or injury if

lifted incorrectly. Lift by lift hook (3) only.

13. Storage

Storage (see „Draining the fuel tank”):

If the plate compactor will not be used for a period

longer than 30 days, follow the steps below to pre-

pare your unit for storage.

1. Drain the fuel tank completely. Stored fuel con-

taining ethanol or MTBE can start to go stale in

30 days. Stale fuel has high gum content and can

clog the carburetor and restrict fuel ow.

2. Start the engine and allow it to run until it stops.

This ensures no fuel is left in the carburetor. Run

the engine until it stops. This helps prevent depos-

its from forming inside the carburetor and possi-

ble engine damage.

3. While the engine is still warm, drain the oil from

the engine. Rell with fresh oil.

4. Let any fuel present drain out of the oat chamber

(see “Cleaning the oat chamber”).

5. Use clean cloths to clean off the outside of the

compactor and to keep the air vents free of ob-

structions.

6. m Do not use strong detergents or petrole-

um based cleaners when cleaning plastic

parts. Chemicals can damage plastics.

7. Store your plate compactor in upright position in a

clean, dry building that has good ventilation.

IM_5904612903_HP2200s_191212_new.indd 29IM_5904612903_HP2200s_191212_new.indd 29 12.12.2019 07:40:2012.12.2019 07:40:20

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Scheppach HP2200S Seite 29

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info