Bedienungsanleitung Scheppach HS116 (Seite 41 von 72) (Deutsch, Englisch, Französisch)

782563

Zoom out

Zoom in

Vorherige Seite

1/72

Nächste Seite

 www.scheppach.com /  service@scheppach.com /  +(49)-08223-4002-99 /  +(49)-08223-4002-58

GB | 41

1. Adjust the parallel stop (8) according to the work-

piece height and the desired width (see 11.4).

2. Place your hands at on the workpiece with your

ngers closed and slide it along the parallel stop

(1) into the saw blade (8).

3. Always push the workpiece through to the end of

the riving knife (3) with the push stick (10).

12.5 Cutting extremely narrow workpieces (g.

36)

Be sure to use a wooden push block (30) when mak-

ing longitudinal cuts in very narrow workpieces with a

width of 50 mm and less.

The wooden push block (30) is not included in the

scope of delivery! (Available from your specialist

dealer) Replace the wooden push block (30) without

delay when it becomes worn.

During sawing, workpieces can become jammed

between the parallel stop (8) and the saw blade

(1), caught by the saw blade (1) and then ejected at

speed. For this reason, the lower guide surface of the

parallel stop (8) should be favoured (see g. 26). Shift

the stop rail (8a) if required (see 11.4.2).

1. Adjust the parallel stop (8) according to the work-

piece height and the desired width (see 11.4).

2. Use the wooden push block (30) to press the

workpiece against the stop rail (8a) and use the

push stick (10) to push the workpiece through to

the end of the riving knife (3).

12.6 Cutting chipboard

To prevent the cutting edges from breaking when cut-

ting chipboard, proceed as follows:The saw blade (1)

must not be set higher than 5 mm above the thick-

ness of the workpiece (see also 11.2).

12.7 After sawing

1. Switch o󰀨 the circular table saw rst and then the

extraction system. The saw blade continues to

run for a longer time.

2. Disconnect the circular table saw from the mains

by pulling the mains plug out of the power socket.

3. Do not remove the cut waste on the saw table until

the saw blade has returned to its resting position.

4. Allow the circular table saw to cool down complete-

12.8 Removing trapped material

m WARNING

Danger of injury for ngers and hands due to sharp

edges

- Wear protective gloves.

• If the saw blade is jammed in the workpiece or oth-

er blockages occur, proceed as follows: Switch the

circular table saw o󰀨 immediately and remove the

mains plug from the socket.

2. When sawing, the saw blade guard (2) is pushed

by the workpiece.

3. Switch on the extraction system and then the cir-

cular table saw.

4. Place your hands at on the workpiece with your

ngers closed and slide it along the parallel stop

(8) into the saw blade (1).

5. Guide the workpiece sideways by holding it only

with the left hand up to the front edge of the saw

blade guard (2).

6. Always push the workpiece through to the end of

the riving knife (3) with the push stick (10).

12.2.1 Performing angled cuts (g. 33)

Angled cuts are always made using the parallel stop

(8). The parallel stop (8) must always be tted to the

right of the saw blade (1) (not shown). Otherwise,

workpieces can become jammed between the paral-

lel stop (8) and the saw blade (1) during sawing and

ejected at speed.

1. Set the saw blade (1) to the desired angle (see

11.3).

2. Adjust the parallel stop (8) according to the work-

piece height and the desired width (see 11.4).

3. Lower the saw blade guard (2) onto the saw table

(5).

4. Make the cut according to the workpiece width

(see 12.2).

12.3 Performing longitudinal cuts (g. 34)

m WARNING

Risk of injury from rotating parts and sharp edges

- Hold the workpiece rmly.

- Push the workpiece with the transverse stop un-

til it is completely cut through.

1. Set the transverse stop (19) as required (see

g. 11.5.1). If the saw blade (1) is also inclined,

push the transverse stop (19) into the right guide

groove. This will prevent your hand and the trans-

verse stop (19) from coming into contact with the

saw blade guard (2).

2. Lower the saw blade guard (2) onto the saw ta-

ble (5). When sawing, the saw blade guard (2) is

pushed by the workpiece.

3. Firmly press the workpiece against the transverse

stop (19).

4. Switch on the extraction system and then the cir-

cular table saw.

5. To make the cut, slide the transverse stop (19) and

the workpiece in the direction of the saw blade (1).

12.4 Cutting narrow workpieces (g. 35)

Be sure to use a push stick (10) when making longitu-

dinal cuts in workpieces smaller than 120 mm in width.

With short workpieces, use the push stick (10) from

the beginning.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Scheppach HS116 Seite 41

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info