Bedienungsanleitung Scheppach HS116 (Seite 40 von 72) (Deutsch, Englisch, Französisch)

782563

Zoom out

Zoom in

Vorherige Seite

1/72

Nächste Seite

 www.scheppach.com /  service@scheppach.com /  +(49)-08223-4002-99 /  +(49)-08223-4002-58

40 | GB

11.7 Using the sliding carrier plate (g. 31)

1. To use the sliding carrier plate (21), pull down the

wing nut (21a) and turn it 90°.

2. Release the wing nut (21a) again so that it engag-

es again.

3. The sliding carrier plate (21) is unlocked and you can

freely move it forwards and backwards.

4. To lock the sliding carrier plate (21), bring it back to

its starting position.

5. Pull the wing nut (21a) down and turn it 90° again.

6. Release it so that it engages again.

7. The sliding carrier plate (21) is locked.

12. Sawing

m WARNING

Danger of injury due to incorrect mounting

- Check that the product is properly assembled.

- Check the saw blade for mobility and the moving

parts for ease of movement.

ATTENTION

Wait after the saw has been switched on, until the

saw blade (1) has reached full speed, before starting

the cutting process.

12.1 Working instructions

m WARNING

Danger of injury!

Improper handling may result in serious injury.

- Observe and follow the safety and working in-

structions.

• When making longitudinal cuts, do not stand in front

of the circular table saw, but position yourself at an

angle to the cut.

• Always use the parallel stop for angled cuts.

• Use a push stick or wooden push block in order to

guide the workpiece past the saw blade. Replace a

damaged or worn push stick.

• Secure larger workpieces against tipping after the

cutting process. To do so, use for example a reel-

o󰀨 stand.

• After the circular table saw has been switched on,

wait until the saw blade has reached full speed, be-

fore starting the cutting process.

• Only operate the table saw with an extraction system.

• After every new setting, we recommend performing

a test cut, in order to check the dimensional settings.

• Check and clean the extraction channels at regular

intervals.

12.2 Performing longitudinal cuts (g. 32)

With a longitudinal cut, you cut a workpiece in its lon-

gitudinal direction. Hold the edge of the workpiece

against the parallel stop (8), whilst the at side lies on

the saw table (5).

1. Adjust the parallel stop (8) according to the work-

piece height and the desired width (see 11.4).

2. Set the saw blade (1) to the maximum cutting

depth. (see 11.2)

3. Position the parallel stop (8) such that the stop rail

(8a) makes contact with the saw blade (1).

4. If the stop rail (8a) is not in line with the saw blade

(1), loosen the hexagon screws (8c) in the parallel

stop (8) with a hexagon spanner and align the stop

rail (8a) parallel to the saw blade (1).

5. Tighten the hexagon screws (8c) again.

6. Again, position the parallel stop (8) away from the

saw blade (1).

11.5 Using the transverse stop (Fig. 23)

Do not push the stop rail (19b) too far towards the saw

blade (1). The distance between the stop rail (19b)

and the saw blade (1) needs to be approx. 2 cm.

11.5.1 Setting the transverse stop (g. 23)

1. Secure the stop rail (19b) on the transverse stop

(19) by tightening the knurled nuts (19d).

2. Slide the transverse stop (19) into one of the two

guide grooves of the saw table (5).

3. Loosen the clamping handle (19c) and turn the trans-

verse stop (19) until the desired angle has been set.

4. Tighten the clamping handle (19c) again.

5. To secure the transverse stop (19) on the slid-

ing carrier plate (21), tighten the wing nut for the

transverse stop (19f).

11.5.2 Using the screw clamp on the transverse

stop (g. 23)

1. Fit the screw clamp (19a) on the transverse stop

(19).

2. Secure the screw clamp (19a) on the required

height by tightening the wing nut for the screw

clamp (19e).

11.6 Table width extensions

11.6.1 Pulling out the left table width extension

(g. 29)

1. To pull out the left table width extension (20), loos-

en the two wing nuts (20a) on the front and rear of

the machine.

2. Pull out the left table width extension (20) to the

desired length.

3. Secure this position by tightening the two wing

nuts (20a) again.

11.6.2 Pulling out the right table width extension

(g. 1 + 30)

1. To pull out the right table width extension (20),

loosen the locking lever for the right table width

extension (11). (g. 1)

2. Pull out the right table width extension (9) to the

desired length. (g. 30)

3. Secure this position by tightening the locking lever

for the right table width extension (11) again.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Scheppach HS116 Seite 40

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info