Bedienungsanleitung Scheppach KP-210 Bamato (Seite 26 von 48) (Deutsch, Englisch, Französisch)

782508

Zoom out

Zoom in

Vorherige Seite

1/48

Nächste Seite

26 GB

AMATO

Bavarian Machine Tools

• Use the tool that is recommended in this manual.

In doing so, your mitre saw provides optimal per-

formance.

• Hands may never enter the processing zone when

the machine is in operation. Release the handle

button and switch off the machine prior to any op-

erations.

7. Before starting the equipment

• The equipment must be set up where it can stand

securely. Secure the machine on a workbench or a

stand with 4 screws through the holes in the xed

saw table (15).

• All covers and safety devices have to be properly

tted before the equipment is switched on.

• It must be possible for the blade to run freely.

• When working with wood that has been processed

before, watch out for foreign bodies such as nails

or screws, etc.

• Before you press the ON/OFF switch check that

the saw blade is tted correctly. Moving parts must

run smoothly.

• Before you connect the equipment to the power

supply make sure the data on the rating plate are

dentical to the mains data.

Do not use the tool if the switch does not allow

you to switch from the ON state to the OFF state.

8. Attachment and operation

8.1 Attaching the saw (Fig1/2/3/4/5)

• In order to adjust the rotary table (14) loosen the

set screw (26) approx. 2 turns.

• Turn the rotary table (14) and pointer (12) to the

desired angle measurement on the scale (13) and

secure with the set screw (26).

• Pressing the machine head (4) lightly downwards

and removing the locking bolt (23) from the motor

bracket at the same time disengages the saw from

the lowest position.

• Swing the machine head (4) up until the release

lever (3) latches into place.

• It is possible to secure the clamping device (7) to

the left or right on the stationary saw bench (15).

Insert the clamping device (7) in the hole on the rear

side of the stop rail (16) and secure it with the star

grip screw (7a).

• Attach the workpiece supports (8) to the xed saw

table (15) as shown in Figure 5 and fasten with the

screw (9).

• It is possible to tilt the machine head (4) a max. 45°

to the left by loosening the set screw (22).

Noise

Total noise values determined in accordance with

EN 61029.

sound pressure level LpA 99.6 dB(A)

uncertainty KpA 3 dB

sound power level LWA 112.6 dB(A)

uncertainty KWA 3 dB

Wear hearing protection.

The effects of noise can cause a loss of hearing.

Vibration emission value ah≤ 2.5 m/s²

uncertainty K 1.5 m/s²

The specied vibration value was established in ac-

cordance with a standardized testing method. It may

change according to how the electric equipment is

used and may exceed the specied value in excep-

tional circumstances;

The specied vibration value can be used to compare

the equipment with other electric power tools.

The specied vibration value can be used for initial

assessment of a harmful effect.

Reduce noise generation and vibration to a mini-

mum!

Use only equipment that is in perfect condition.

Maintain and clean the equipment regularly.

Adopt your way of working to the equipment.

Do not overload the equipment.

Have the equipment checked if necessary.

Switch off the equipment when not in use.

Residual risks

The machine has been built according to the state

of the art and the recognised technical safety re-

quirements. However, individual residual risks

can arise during operation.

• Health hazard due to electrical power, with the use

of improper electrical connection cables.

• Furthermore, despite all precautions having been

met, some non-obvious residual risks may still re-

main.

• Residual risks can be minimised if the „safety in-

structions“ and the „Proper use“ are observed

along with the whole of the operating instructions.

• Do not load the machine unnecessarily: excessive

pressure when sawing will quickly damage the saw

blade, which results in reduced output of the ma-

chine in the processing and in cut precision.

• When cutting plastic material, please always use

clamps: the parts which should be cut must always

be xed between the clamps.

• Avoid accidental starting of the machine: the op-

erating button may not be pressed when inserting

the plug in an outlet.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Scheppach KP-210 Bamato Seite 26

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info