Bedienungsanleitung Scheppach KP-210 Bamato (Seite 28 von 48) (Deutsch, Englisch, Französisch)

782508

Zoom out

Zoom in

Vorherige Seite

1/48

Nächste Seite

28 GB

AMATO

Bavarian Machine Tools

8.8 Limiting the cutting depth (Fig. 3/14)

• The cutting depth can be innitely adjusted using

the screw (24). To do this loosen the knurled nut on

the screw (24). Move the stop for the cutting depth

limitre (25) to the outside. Turn the screw (24) in

or out to set the required cutting depth. Then re-

tighten the knurled nut on the screw (24).

• Check the setting by completing a test cut.

8.9 Sawdust bag (Fig. 1)

The saw is equipped with a debris bag (17) for saw-

dust and chips.

Squeeze together the metal ring on the dust bag and

attach it to the outlet opening in the motor area.

The debris bag (17) can be emptied by means of a

zipper at the bottom.

8.10 Changing the saw blade (Fig. 15/16/17/18)

Remove the power plug!

Important.

Wear safety gloves when changing the saw blade.

Risk of injury!

• Swing up the machine head (5).

• Undo the screw (e) on the guide bar (37), so that it

can move freely and be pivoted downwards.

• Press the release lever (3). Swing up the saw blade

guard (6) to the point where the recess in the saw

blade guard (6) is above the ange bolt (31).

• Press the saw shaft lock (4) with one hand. With the

other hand insert the allen key (d) in the ange bolt

(31).

• Hold the Allen key (d) and slowly close the saw

blade guard until it touches the Allen key.

• Firmly press the saw shaft lock (4) and slowly rotate

the ange bolt (31) in clockwise direction. The saw

shaft lock (4) engages after no more than one rota-

tion.

• Now, using a little more force, slacken the ange

bolt (31) in the clockwise direction.

• Turn the ange screw (31) right out and remove the

external ange (32).

• Take the blade (7) off the inner ange (38) and pull

out downwards.

• Carefully clean the ange screw (31), outer ange

(32) and inner ange (38).

• Fit and fasten the new saw blade (7) in reverse order.

• Important! The cutting angle of the teeth, in other

words the direction of rotation of the saw blade (7)

must coincide with the direction of the arrow on

the housing.

• Move the guide bar (37) into position and tighten

the screw (e) again.

• Before continuing your work make sure that all

safety devices are in good working condition.

• Important! Every time that you change the saw

blade (7), check to see that it spins freely in the

table insert (11) in both perpendicular and 45° an-

gle settings.

8.6 Mitre cut 0°- 45° and turntable 0° (Fig. 1/2/12)

The crosscut saw can be used to make mitre cuts of

0° - 45° in relation to the work face.

Important. To make miter cuts (inclined saw head),

the adjustable stop rail (16a) must be xed at the

outer position.

• Open the set screw (16b) for the adjustable stop

rail (16a) and push the adjustable stop rail out-

wards.

• The adjustable stop rail (16a) must be xed far

enough in front of the innermost position that the

distance between the stop rail (16a) and the saw

blade (6) amounts to a maximum of 8 mm.

• Before making a cut, check that the stop rail (16a)

and the saw blade (6) cannot collide.

• Secure the set screw (16b) again.

• Move the machine head (4) to the top position.

• Fix the rotary table (14) in the 0° position.

• Loosen the set screw (22) and use the handle (1)

to angle the machine head (4) to the left, until the

pointer (19) indicates the desired angle measure-

ment on the scale (18).

• Re-tighten the xing screw (22).

• Cut as described in section 8.3.

8.7 Mitre cut 0°- 45° and turntable 0°- 45°

(Fig. 2/4/13)

The crosscut saw can be used to make mitre cuts to

the left of 0°- 45° in relation to the work face and, at

the same time, 0° - 45° to the left or 0° - 45° to the

right in relation to the stop rail (double mitre cut).

Important. To make miter cuts (inclined saw head),

the adjustable stop rail (16a) must be xed at the

outer position.

• Open the set screw (16b) for the adjustable stop

rail (16a) and push the adjustable stop rail out-

wards.

• The adjustable stop rail (16a) must be xed far

enough in front of the innermost position that the

distance between the stop rail (16a) and the saw

blade (6) amounts to a maximum of 8 mm.

• Before making a cut, check that the stop rail (16a)

and the saw blade (6) cannot collide.

• Secure the set screw (16b) again.

• Move the machine head (4) to its upper position.

• Release the rotary table (14) by loosening the set

screw (26).

• Using the handle (11), set the rotary table (14) to

the desired angle (refer also to point 8.4 in this

regard).

• Re-tighten the set screw (26) in order to secure

the rotary table.

• Undo the locking screw (22) and use the handle (1)

to tilt the machine head (4) to the left until it coin-

cides with the required angle value (in this connec-

tion see also section 8.6).

• Re-tighten the xing screw (22).

• Cut as described under section 8.3.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Scheppach KP-210 Bamato Seite 28

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info