Bedienungsanleitung Scheppach KP-210 Bamato (Seite 29 von 48) (Deutsch, Englisch, Französisch)

782508

Zoom out

Zoom in

Vorherige Seite

1/48

Nächste Seite

AMAT

Bavarian Machine Tools

If the carbon is worn to a length of 6 mm, or if the

spring or contact wire are burned or damaged, it is

necessary to replace both brushes. If the brushes are

found to be usable following removal, it is possible to

reinstall them.

Service information

Please note that the following parts of this product are

subject to normal or natural wear and that the follow-

ing parts are therefore also required for use as con-

sumables.

Wear parts*: Carbon brush, saw blade, battery, table

insert, sawdust bag, V-belts

* Not necessarily included in the scope of delivery!

11. Storage

Store the device and its accessories in a dark, dry

and frost-proof place that is inaccessible to children.

The optimum storage temperature is between 5 and

30˚C.

Store the electrical tool in its original packaging.

Cover the electrical tool in order to protect it from

dust and moisture.

Store the operating manual with the electrical tool.

12. Electrical connection

The electrical motor installed is connected and

ready for operation. The connection complies

with the applicable VDE and DIN provisions.

The customer‘s mains connection as

well as the extension cable used must al-

so comply with these regulations.

• The product meets the requirements of EN

61000-3-11 and is subject to special connection

conditions. This means that use of the product at

any freely selectable connection point is not al-

lowed.

• Given unfavorable conditions in the power supply

the product can cause the voltage to uctuate tem-

porarily.

• The product is exclusively intended for use at con-

nection points that have a continuous current-car-

rying capacity of at least 100 A per phase.

• As the user, you are required to ensure, in consul-

tation with your electric power company if neces-

sary, that the connection point at which you wish

to operate the product meets the specied require-

ments.

Important information

In the event of an overloading the motor will switch

itself off. After a cool-down period (time varies) the

motor can be switched back on again.

• Important! The work to change and align the saw

blade (7) must be carried out correctly.

8.11 Using the laser (Fig. 3/19/20)

• To switch on: Move the ON/OFF switch of the la-

ser (34) to the “1” position. A laser line is projected

onto the material you wish to process, providing an

exact guide for the cut.

• To switch off: Move the ON/OFF switch of the la-

ser (34) to the “0” position.

• Replacing the battery: Switch off the laser

(33). Remove the battery compartment cov-

er (36). Remove the batteries and replace with

new batteries (2 x 1.5 Volt Type LR 03 Micro,

AAA) Check that the battery terminals are po-

sitioned correctly when inserting new batter-

ies. Close the battery compartment (35) again.

8.12 Adjusting the laser (Fig. 21)

If the laser (33) ceases to indicate the correct cutting

line, you can readjust the laser. To do so, open the

screws (38) and set the laser by moving sideways to

that the laser beam strikes the teeth of the saw blade

(6).

9. Transport

• Tighten the set screw (26) in order to lock the ro-

tary table (14)

• Activate the release lever (3), press the machine

head (4) downwards and secure with the safety pin

(23). The saw is now locked in its bottom position.

• Fix the saw’s drag function with the locking screw

for drag guide (20) in rear position.

• Carry the equipment by the xed saw table (15).

• When reassembling the equipment proceed as de-

scribed under section 7.

10. Maintenance

m Warning! Prior to any adjustment, maintenance or

service work disconnect the mains power plug!

General maintenance measures

Wipe chips and dust off the machine from time to time

using a cloth. In order to extend the service life of the tool,

oil the rotary parts once monthly. Do not oil the motor.

When cleaning the plastic do not use corrosive prod-

ucts.

Brush inspection

Check the carbon brushes after the rst 50 operat-

ing hours with a new machine, or when new brushes

have been tted. After carrying out the rst check, re-

peat the check every 10 operating hours.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Scheppach KP-210 Bamato Seite 29

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info